PLC_9000 – Access error to a machine data or the value of the machine data
PLC_9001 – Thermal relays KO
PLC_9002 –
PLC_9003 –
PLC_9004 – Inverter Emergency
PLC_9005 – NC Emergency
PLC_9006 – The dimensions of the panel are not suitable for the surfacing cycle
PLC_9007 – Slot reset required
PLC_9008 – TP Reset Required for Manual Tool-Change Operation
PLC_9009 – Cycle stop from LH safety area device
PLC_9010 – Cycle stop from RH safety area device
PLC_9011 – Insufficient vacuum
PLC_9012 – Cabinet température alarme
PLC_9013 – Insufficient vacuum in LH area
PLC_9014 – Insufficient vacuum in RH area
PLC_9015 – Standard work list is enabled.
PLC_9016 – The independent work list on two tables is enabled.
PLC_9017 – You don’t specify correctly the working table in the work list. It will be used the table number 1.
PLC_9018 – The selected origin is not compatible with the working table.
PLC_9019 – Incompatible instructions
PLC_9020 – End of program without TP0, T0, TH0 (1=TP, 2=T, 3=TH)
PLC_9021 – The tool is temporarily unavailable, because it is used by another TP
PLC_9022 – ATTENZIONE: LA MACCHINA E’ IN SIMULAZIONE.
PLC_9023 – ATTENZIONE: IL LIVELLO DELLA PASSWORD NON E’ ADEGUATO PER LA SIMULAZIONE MACCHINA.
PLC_9024 – Attention: axis braking resistor KO. Contact the Assistance Service immediately.
PLC_9025 – The machine switch-on button can be pressed
PLC_9026 – Warning at least a running program
PLC_9027 –
PLC_9028 – Warning! Timeout expired, contact mat control unit not reset
PLC_9029 – Warning! Cannot turn the machine on, possible inverter errors
PLC_9030 – M instruction error
PLC_9031 – The axis speed has been reduced due to the presence of a panel whose Y (LPY) dimension exceeds the limit (LimMinLPY)
PLC_9032 – Sequential zone locking mode has been selected: one zone will be locked in sequence each time the pedal is pressed
PLC_9033 – Sequential zone locking mode has been selected: to release the pieces, use the pedal or remote console
PLC_9034 – The maximum safety speed for axis X has been exceeded
PLC_9035 – Machine in emergency mode due to unscheduled engagement of the photocell (Start button on the column pressed)
PLC_9036 – Photocell engagement booking performed
PLC_9037 – Impossible command. The vertical axis is not in a parked position or has not been zero-set
PLC_9038 – Axis drive KO
PLC_9039 – Warning: the panel will not be locked due to the dimensions smaller than the usable surface of the locking area
PLC_9040 – PLC MANUAL RESET NOT ENABLED: CYCLE INTERRUPTED
PLC_9041 – It is not possible to zero-set the axes. Untool the TP with cumbersome aggregate (MODE datum other than 0)
PLC_9042 – Safety command error for TPs tooled with cumbersome aggregates
PLC_9043 – To reset the TP tooled with cumbersome aggregate, zero-set the Rotative axis in Single mode
PLC_9044 – Machine suspension caused by TP
PLC_9045 – Warning photocells occupied. To reset the photocells press the button on the machine and then the Start button on the pedestal
PLC_9046 – TP Tool-present Sensor Lacking
PLC_9047 – TP with manually released tool manuellement
PLC_9048 – Warning,are using a Z offset or thickness cups negative. Make sure that the suction cups on the carriage are all the correct thickness. Press the Origin Start button to continue.
PLC_9049 – No band sensor down
PLC_9050 – Axis stopped with the flag NOEXEC at 1
PLC_9051 – Horizontal photocells occupied
PLC_9052 – Waiting for inverter stopped
PLC_9053 – Operation impossible due to vertical dimensions
PLC_9054 – TP motor overload cutout KO
PLC_9055 – The band has been commanded up, but has remained down
PLC_9056 – Band down sensor off
PLC_9057 – Band not idle
PLC_9058 – The the slide position input is not stable
PLC_9059 – The slide is no longer in the position to which it was commanded
PLC_9060 – It is not possible to unlock the tool due to the rotation of the spindles
PLC_9061 – Machine suspension due to inverter stoppage.
PLC_9062 – Security inverter input inactive with sled at rest (sled, input)
PLC_9063 – Inverter warning , press emergency and clear (number inverter)
PLC_9064 – Error when setting the positioned suspension data
PLC_9065 – Timeout bidirectional cutter locking
PLC_9066 – No band sensor up
PLC_9067 – The program started with the HSK electrospindle not tooled up. Tool it up.
PLC_9068 – Attention: machine emergency due to an error on the axis X safety card
PLC_9069 – The tool sensor on TP is active
PLC_9070 –
PLC_9071 – Both step counting and suction box up sensors are active
PLC_9072 – The button for the offset calculation or sensor initialisation procedure has been released too early
PLC_9073 – The offset calculation or sensor initialisation procedure has been successfully completed
PLC_9074 – At least one magnet of a carriage or table is not detected
PLC_9075 – Procedure for the detection of the tables. The table was not detected or was not brought to the correct position “QuotaAzPi”
PLC_9076 – Procedure for the detection of the carriages. The carriage was not detected or was not brought to the correct position “QuotaAzCa”
PLC_9077 – Error in the sensor initialisation procedure for the assisted table module: the magnets are present on the table and/or carriage
PLC_9078 – Warning: program without work table tooling.
PLC_9079 – The module for table/carriage position management is not working correctly
PLC_9080 – Initialisation request not accepted
PLC_9081 – The tables and/or carriages are not in the correct position. The position of the tables and/or carriages may have been lost. Press Stop Reset and relaunch the programme.
PLC_9082 – Warning: it is possible to proceed with the locking process by pressing the origin start
PLC_9083 – Warning: the carriages are unlocked. Lock the carriages to proceed with tooling
PLC_9084 – Presser up sensor missing
PLC_9085 –
PLC_9086 –
PLC_9087 –
PLC_9088 –
PLC_9089 – TP positioning timeout
PLC_9090 – Boring machine positioning timeout
PLC_9091 –
PLC_9092 –
PLC_9093 – Unsuccessful inverter transmission
PLC_9094 – Timeout Stopped motor input
PLC_9095 – Motor stopped input remains with inverter running at normal speed
PLC_9096 – Buffered Ram KO
PLC_9097 – Buffered Ram Too Small
PLC_9098 – AXIS LUBRICATION SEQUENCE ACTIVATED
PLC_9099 – HEADS LUBRICATION SEQUENCE ACTIVATED
PLC_9100 – System Lubrication Time Run Out
PLC_9101 – System Lubricant Non Present
PLC_9102 – Lubrication Cycle Microswitch Malfunctioning OK System
PLC_9103 – HEAD LUB. KO: MACHINE NOT ON(2) NC ACTIVE(4) SLOTS NOT RESET(16) PROG ACTIVE(32)
PLC_9104 – LUBRICATION CORRECTLY COMPLETED SYSTEM
PLC_9105 – Attempt to unload from untooled TP
PLC_9106 – Cone opening timeout
PLC_9107 – Cone closing timeout
PLC_9108 – TP on inactive slot
PLC_9109 – TP without automatic tool change
PLC_9110 – WARNING: CHECK THE LUBRICATION SYSTEM (CALL BIESSE SERVICE)
PLC_9111 – Number of tool holder on magazine onboard machine incorrect
PLC_9112 – Load from empty tool holder of magazine onboard machine
PLC_9113 – Unload to occupied tool holder of magazine onboard machine
PLC_9114 – Load on occupied electrospindle from magazine onboard machine
PLC_9115 – Unload from empty electrospindle from magazine onboard machine
PLC_9116 – KB failed on magazine onboard machine
PLC_9117 – WARNING: THE BORING MACHINE MOTOR IS IDLE. Press STOP-RESET
PLC_9118 – At least one tool load attempt from magazine onboard machine has failed
PLC_9119 – Tool-Holder Ascent Command With Closed Magazine
PLC_9120 – Error in moving cover of magazine onboard machine
PLC_9121 – Number of magazine onboard machine incorrect
PLC_9122 – Error in moving tool holder of magazine onboard machine
PLC_9123 – Number of electrospindle in magazine onboard machine incorrect
PLC_9124 – Error in moving horizontal movement piston of magazine onboard machine
PLC_9125 – Slot not enabled for tool change on magazine onboard machine
PLC_9126 – WARNING: INSUFFICIENT NUMBER OF ACTIVATIONS GENERATED
PLC_9127 – WARNING: REQUEST BORING HEAD MANUAL LUB. REFUSED: spindle T/TH are not equipped.
PLC_9128 – Can not command the tool holder down. Remove the tool from the tool holder and remove the tool from the magazine tooling
PLC_9129 – Can not command the tool holder up. I the CN equipping the tool on the tool holder
PLC_9130 – There are free not tools holder free on the fast magazine. The tooling of the magazine is not completed.
PLC_9131 – Was not found a slow magazine to download the tool. The setup of the magazine is not complete
PLC_9132 – In the set configuration there is no a SET to the required pantograph
PLC_9133 – Using configurations. The destination magazine must be not equipped (without tools)
PLC_9134 – At least one tool that will use the deflector is present in the fast magazine, that is not enabled for the deflector, you should download the tool but there are no free tool holder
PLC_9135 – A tool requesting can not be managed by automatic setup. Analyze the log file for details.
PLC_9136 – A tool is not eligible to be managed by automatic setup. Analyze the log file for details.
PLC_9137 – WARNING: REQUEST THELUBRICATION OF THE BORING HEAD. Press STOP-RESET.
PLC_9138 – Revolver magazine number error
PLC_9139 – Revolver tool holder number error
PLC_9140 – TP number for revolver tool change incorrect
PLC_9141 – The MAGREV->DeltTest datum necessary for the cone test is too high. It will be automatically reset
PLC_9142 – Slot not enabled for tool change on revolver type magazine
PLC_9143 – Unable to control the magazine cover with the tooling selector active. Open the cover of the magazine with the machine is power
PLC_9144 – Data error of the integrated deflector on the tool/aggregate of TP
PLC_9145 – At least one tool unload attempt from magazine onboard machine has failed
PLC_9146 – At least one tool unload attempt from revolver magazine has failed
PLC_9147 – At least one tool unload attempt from chain magazine has failed
PLC_9148 – Unload cycle of a tool failed (TP number; tool name)
PLC_9149 – Load cycle of a tool failed (TP number; tool name)
PLC_9150 – Revolver removal piston error
PLC_9151 – Some pocket of magazine onboard are enabled.
PLC_9152 – Number of tool holder on magazine onbridge incorrect
PLC_9153 – Number of magazine onbridge incorrect
PLC_9154 – Number of electrospindle in magazine onbridge incorrect
PLC_9155 – Error on revolver type tool magazine cover
PLC_9156 – Slot not enabled for tool change on magazine onbridge
PLC_9157 – Load on occupied electrospindle from magazine onbridge
PLC_9158 – Load from empty tool holder of magazine onbridge
PLC_9159 – At least one tool load attempt from magazine onbridge has failed
PLC_9160 – Unload from empty electrospindle from magazine onbridge
PLC_9161 – Attempt to load from empty revolver tool holder
PLC_9162 – Attempt to unload on busy revolver tool holder
PLC_9163 – Revolver magazine generic error: reset required
PLC_9164 – Unload to occupied tool holder of magazine onbridge
PLC_9165 – Attempt to load from revolver on tooled TP
PLC_9166 – Attempt to unload on revolver from untooled TP
PLC_9167 – At least one tool unload attempt from magazine onbridge has failed
PLC_9168 – KB failed at tool change on revolver type tool magazine
PLC_9169 – The tool magazine related to the magazine onbridge is not in the rest position
PLC_9170 – Error in moving movement piston of magazine onbridge
PLC_9171 – Magazine onbridge configuration is not valid
PLC_9172 – Reset failed. To try new reset place machine in emergency and then restore power
PLC_9173 – Cannot command the magazine cover: axis X position not correct
PLC_9174 – The mode locking is not congruent with the type of plan
PLC_9175 – Machine suspended. The right or left limit of the X axis, in relation to the side of the panel, has been exceeded
PLC_9176 – Selected TP not enabled for tool change
PLC_9177 – Selected Pick-up pocket does not exist
PLC_9178 – Selected magazine not present in machine
PLC_9179 – Selected magazine pocket does not exist
PLC_9180 – Pocket or TP without tool
PLC_9181 – Destination Pocket or TP not free
PLC_9182 – Tool change cycle not possible with a program in progress
PLC_9183 –
PLC_9184 –
PLC_9185 –
PLC_9186 –
PLC_9187 –
PLC_9188 –
PLC_9189 –
PLC_9190 – Error: robot disabled – there are 2 robot-tables active
PLC_9191 – Robot in emergency
PLC_9192 – Cycle stop by Robot on LH area
PLC_9193 – Cycle stop by Robot on RH area
PLC_9194 –
PLC_9195 –
PLC_9196 – Machine suspended: not down lateral stops are interfering with the tool change on the machine-side magazine
PLC_9197 –
PLC_9198 –
PLC_9199 –
PLC_9200 –
PLC_9201 –
PLC_9202 –
PLC_9203 – Magazine onboard carriage in incorrect position
PLC_9204 –
PLC_9205 –
PLC_9206 – Error: input lost for the unlock tool sensor
PLC_9207 –
PLC_9208 –
PLC_9209 –
PLC_9210 – Tooling of magazine is not allowed: the magazine is busy from machine.
PLC_9211 – Command on magazine blocked: magazine in tooling.
PLC_9212 – Command not accepted from remote control: magazine door open.
PLC_9213 – Command not accepted from remote control: tooling of magazine disabled.
PLC_9214 –
PLC_9215 –
PLC_9216 –
PLC_9217 –
PLC_9218 –
PLC_9219 –
PLC_9220 – ATTENTION: possible collision between PANEL and AGGREGATES on REVOLVER magazine. Check the panel thickness.Press Stop+Reset.
PLC_9221 – Cleaning cycle: toolaggregate not enabled
PLC_9222 – Cleaning cycle: toolaggregate not valid
PLC_9223 – Cleaning cycle error
PLC_9224 – Cleaning cycle: Bistable ascent/descent KO
PLC_9225 –
PLC_9226 –
PLC_9227 –
PLC_9228 –
PLC_9229 –
PLC_9230 –
PLC_9231 –
PLC_9232 –
PLC_9233 –
PLC_9234 –
PLC_9235 –
PLC_9236 –
PLC_9237 –
PLC_9238 –
PLC_9239 –
PLC_9240 –
PLC_9241 –
PLC_9242 –
PLC_9243 –
PLC_9244 –
PLC_9245 –
PLC_9246 –
PLC_9247 –
PLC_9248 –
PLC_9249 –
PLC_9250 –
PLC_9251 –
PLC_9252 –
PLC_9253 –
PLC_9254 –
PLC_9255 –
PLC_9256 –
PLC_9257 –
PLC_9258 –
PLC_9259 –
PLC_9260 –
PLC_9261 –
PLC_9262 –
PLC_9263 –
PLC_9264 –
PLC_9265 –
PLC_9266 – Work list: Error in PLC-NC communication
PLC_9267 – The deflector for the TP is not present in the magazine or is present on a tool holder on which the TP is off
PLC_9268 – Piece counter greater than or equal to amount to manufacture
PLC_9269 –
PLC_9270 –
PLC_9271 – The requested position for the hood is not compatible with the maximum diameter of the tool/aggregate present on the TP.
PLC_9272 –
PLC_9273 –
PLC_9274 –
PLC_9275 –
PLC_9276 –
PLC_9277 –
PLC_9278 –
PLC_9279 –
PLC_9280 –
PLC_9281 –
PLC_9282 – Electrical cabinet overload cutout KO
PLC_9283 –
PLC_9284 – Series: manual tooling – cable – mesh gates – boring unit cover – CE cams – NC watchdog: KO
PLC_9285 – Mushroom emergency button on electrical cabinet pressed or on remote override control.
PLC_9286 –
PLC_9287 –
PLC_9288 – Insufficient pressure to release the cone
PLC_9289 –
PLC_9290 – Reset RAM Ok!
PLC_9291 –
PLC_9292 – Both sensors active
PLC_9293 – The inputs of the lockunlock are both active on the electrospindle
PLC_9294 –
PLC_9295 – Tool presence test cycle incompatible with the RESET environment: cycle interrupted or not started
PLC_9296 –
PLC_9297 – (!) Generic PLC error (analyse the log file)
PLC_9298 – The gantry working distance of the two front and rear carriages is below the permitted value
PLC_9299 – Error: at least one of the selected spindles does not have a vertical axis
PLC_9300 – An axis that does not belong to the selected spindles is slave to an axis of the reference spindle
PLC_9301 – An axis of the selected spindles is already slave to another axis
PLC_9302 – A slave axis of another axis has been commanded from the PLC
PLC_9303 – TP not equipped
PLC_9304 – Error: no spindles selected
PLC_9305 – Reset not possible: the axes associated to the benches are in MASTER/SLAVE mode
PLC_9306 –
PLC_9307 – Incorrectly set vertical safety distance
PLC_9308 – The spindles to be activated are the same that have been selected
PLC_9309 – Equipping data error of the tool holder deflector: the deflector is not present in its tool holder and on any TP
PLC_9310 – Several TP slide sensors are active
PLC_9311 – Several boring machine slide sensors are active
PLC_9312 – The TP is not idle
PLC_9313 – The boring machine is not idle
PLC_9314 – The TP suction box is not idle
PLC_9315 – The boring machine suction box is not idle
PLC_9316 – The TP presser is not idle
PLC_9317 – Input parameters error of the cycle being carried out
PLC_9318 – At least one of the selected spindles is not compatible with the program execution centre
PLC_9319 – Error: the MONOCENTRE programs can not be run at the same time as MULTICENTRE programs
PLC_9320 – Definition error of the processing blocks of a program
PLC_9321 – Belt type tool magazine number incorrect
PLC_9322 – Tool holder number in belt type tool magazine incorrect
PLC_9323 – TP number for tool change in belt type tool magazine incorrect
PLC_9324 – The requested/reached suction box position is not compatible with the machining operation
PLC_9325 – Slot not enabled for tool change on belt type tool magazine
PLC_9326 –
PLC_9327 –
PLC_9328 – Error on belt type tool magazine cover
PLC_9329 – Table suction box movement error
PLC_9330 – Error in movement of suction box with axis
PLC_9331 –
PLC_9332 –
PLC_9333 –
PLC_9334 – Attempt to load from empty tool holder in belt type tool magazine
PLC_9335 – Attempt to unload on busy tool holder in belt type tool magazine
PLC_9336 – Attempt to load from belt type tool magazine on tooled TP
PLC_9337 – Attempt to unload on belt type tool magazine from untooled TP
PLC_9338 – KB failed in tool change on belt type tool magazine
PLC_9339 – Belt type tool magazine generic error: reset required
PLC_9340 – Attention: in the chain type magazine, the tooling data of the toolholder and the test cones results are different
PLC_9341 – Warning: in the revolver tool magazine, the tooling data of the tool holder and the result of the cone test are different
PLC_9342 –
PLC_9343 – Double tool change: inhomogeneous operations (two loading or unloading operations must be programmed)
PLC_9344 – Double tool change: at least one of the two tools to be loaded does not belong to the belt tool magazine (program the two loading operations separately)
PLC_9345 – Double tool change impossible: one of the TPs programmed cannot execute this operation
PLC_9346 – Error on read/write head piston in belt type magazine
PLC_9347 – Too low release in the tool holder
PLC_9348 –
PLC_9349 –
PLC_9350 –
PLC_9351 – Warning: the magazine axis has been commanded, but the read/write head is not in the rest position
PLC_9352 –
PLC_9353 –
PLC_9354 –
PLC_9355 –
PLC_9356 –
PLC_9357 –
PLC_9358 –
PLC_9359 –
PLC_9360 – Flexstore type magazine number incorrect
PLC_9361 – Tool holder number in Flexstore type magazine incorrect
PLC_9362 – The shuttle of the Flexstore is not in parking position, place the axis manually
PLC_9363 – Manual reset of Flexstore shuttle required
PLC_9364 – Flexstore shuttle manual reset failed
PLC_9365 – Flexstore type magazine door open
PLC_9366 – Flexstore: Pressure switch KO
PLC_9367 – Error in the piston of the read/write head of the Flexstore magazine
PLC_9368 – Error in the piston to lock/unlock the cone of the shuttle of the Flexstore magazine
PLC_9369 – Error in the vertical piston of the shuttle of the Flexstore magazine
PLC_9370 – Error in the horizontal piston of the shuttle of the Flexstore magazine
PLC_9371 – Error in the piston to release the shuttle of the Flexstore magazine
PLC_9372 –
PLC_9373 – Attempt to load from tool holder of empty Flexstore type magazine.
PLC_9374 – Attempt to unload on tool holder of busy Flexstore type magazine
PLC_9375 – Attempt to load tool on shuttle of busy Flexstore type magazine
PLC_9376 – Attempt to load from tool holder of empty magazine
PLC_9377 – Attempt to unload on tool holder of busy magazine
PLC_9378 – Tool not present on Flexstore type magazine shuttle.
PLC_9379 – Optimization on external magazine failed.
PLC_9380 – Number of tools used in program exceeds the capacity of the magazine
PLC_9381 – A tool required is not present in flexstore magazine.
PLC_9382 – It is not possible to find an empty pocket or a pocket to unload for a tool in the tool list.
PLC_9383 – It’s necessary to unload a tool required in another executing program. Wait.
PLC_9384 – Laser Error communication (numberLaser, type laser)
PLC_9385 – Optimization external toolchange timeout error
PLC_9386 – Valve communication error (valve number or type)
PLC_9387 – Valve pressure error [bar] (valve number or type, or value set)
PLC_9388 – Valve pressure error – outside range [bar] (valve number or type, value, measurement, tolerance)
PLC_9389 –
PLC_9390 –
PLC_9391 –
PLC_9392 –
PLC_9393 –
PLC_9394 –
PLC_9395 –
PLC_9396 –
PLC_9397 –
PLC_9398 –
PLC_9399 –
PLC_9400 –
PLC_9401 – Carriage reset not possible
PLC_9402 – Warning: program without work table tooling. No movement of work tables and carriages will be performed
PLC_9403 – Error in the requested position for a carriage with manual positioning
PLC_9404 – Timeout in the movement of a work table axis
PLC_9405 –
PLC_9406 –
PLC_9407 –
PLC_9408 –
PLC_9409 – NC environment not compatible
PLC_9410 – Moving tables reset failed
PLC_9411 –
PLC_9412 –
PLC_9413 – Carriages are not moved because they can damage each other
PLC_9414 –
PLC_9415 –
PLC_9416 – Carriage position acquisition cycle error
PLC_9417 –
PLC_9418 – Tool identification cycle: tool holder /magazine not found or not enabled
PLC_9419 – Tool identification cycle: Magazine axis positioning timeout
PLC_9420 – Tool identification cycle: Timeout in test cycle for tool presence in magazine
PLC_9421 – Tool identification cycle: Tool absent
PLC_9422 – Cycle tool identification : not enabled Pocket
PLC_9423 –
PLC_9424 –
PLC_9425 –
PLC_9426 –
PLC_9427 – To run the jigs cycle you must reset the axes
PLC_9428 – To run the jigs cycle the machine must be under power
PLC_9429 –
PLC_9430 – Vacuumuniclamp selector altered
PLC_9431 –
PLC_9432 – Dynamic jig thickness mode enabled. Check that thickness indicated is correct
PLC_9433 –
PLC_9434 – Machine in tooling. Tooling selector (SAT) active
PLC_9435 – Machine non in tooling. Tooling selector (SAT) inactive
PLC_9436 – CAUTION, simulation with spindle off active. No spindle will be started during program
PLC_9437 –
PLC_9438 –
PLC_9439 –
PLC_9440 – Check: emergency button on console, on tooling button pad or on supplementary machine-side button pad has been pressed; operating section covers are open
PLC_9441 –
PLC_9442 –
PLC_9443 – If the machine remains suspended, reset the safety mats by pressing the area selection button
PLC_9444 –
PLC_9445 –
PLC_9446 – Micro of safety hardware cam not detected: check the micro and the relevant hardware cam
PLC_9447 – The machine on button or a START button on the working area button pad is stuck or faulty
PLC_9448 – Emergency triggered by cord/machine-side emergency button
PLC_9449 – The chip conveyor belt has stopped because the motor thermal cutout is ON
PLC_9450 –
PLC_9451 – Axis reset impossible (press STOP-RESET)
PLC_9452 –
PLC_9453 – Axis Y1 and Y2 do not have the same Parked position (QRIP)
PLC_9454 – Stop cycle from central area safety device
PLC_9455 – Insuficient pressure
PLC_9456 – Warning: Low Pressure
PLC_9457 – Axis not aligned
PLC_9458 – Error in axis in MASTER/SLAVE mode
PLC_9459 –
PLC_9460 –
PLC_9461 –
PLC_9462 –
PLC_9463 –
PLC_9464 –
PLC_9465 –
PLC_9466 –
PLC_9467 – Error in one piston: both sensors are active
PLC_9468 – Rest position commanded but does not move
PLC_9469 – Rest position commanded but not reached
PLC_9470 – Excited position commanded but does not move
PLC_9471 – Excited position commanded but not reached
PLC_9472 – Number of tool change magazine incorrect
PLC_9473 – Number of tool change type magazine tool holder incorrect
PLC_9474 – Number of electrospindle for tool change on tool change type magazine incorrect
PLC_9475 – Slot not enabled for tool change on tool change type magazine
PLC_9476 – Error on tool change type magazine
PLC_9477 – Axis cannot move as the Tool Change Magazine is not at the parking position
PLC_9478 – KB failed in tool change on tool change type magazine
PLC_9479 – Impossible to move the tool change magazine to the rest position. Perform the operation manually and start the zeroing
PLC_9480 – Impossible to move the tool change to working position because axis C of the electrospindle is not at rest.
PLC_9481 – In order to use balluff you have to unload the deflector from TP.
PLC_9482 – In order to use balluff you have to unload the tool from TP.
PLC_9483 – The arm of the tool change type magazine is not in the rest position.
PLC_9484 – Attempt to unload to tool change type magazine from untooled electrospindle
PLC_9485 –
PLC_9486 – Error in tool change horizontal release piston.
PLC_9487 – Error in tool change vertical release piston.
PLC_9488 –
PLC_9489 –
PLC_9490 –
PLC_9491 – Error in locking/releasing tool on tool change magazine
PLC_9492 –
PLC_9493 –
PLC_9494 –
PLC_9495 –
PLC_9496 – Tool change type magazine: Impossible to move the axis because the tool lock piston is not at rest.
PLC_9497 –
PLC_9498 –
PLC_9499 –
PLC_9500 – Electrospindle load cycle failed: pick-up from empty tool holder
PLC_9501 – Electrospindle unload cycle failed: deposit on full tool holder
PLC_9502 –
PLC_9503 – Tool change interrupted because the CR axis is not in the correct position
PLC_9504 –
PLC_9505 –
PLC_9506 – Warning: Magazine not at rest, press the button to align the magazine
PLC_9507 –
PLC_9508 – Cannot orientate the TP, because it is not down
PLC_9509 –
PLC_9510 – An axis has been commanded, but the override is 0
PLC_9511 – Electrospindle cooler: check the automatic safety switch, the flow switch of the coolant circuit and the thermal cutout on the pump motor.
PLC_9512 – Caution: check the state of axes before resetting. Press START again to continue.
PLC_9513 – Caution: Increase Override to complete RESET
PLC_9514 – Overload on the braking resistor of the inverter
PLC_9515 – Overload on the braking resistor or resistors of the axis
PLC_9516 –
PLC_9517 – EMERGENCY LINE reset
PLC_9518 – SET OF CONTACTORS not reset: at least one contactor has remained enabled
PLC_9519 – SET OF CONTACTORS reset
PLC_9520 – If the machine does not power up, check proper functioning of the safety device
PLC_9521 –
PLC_9522 – If the suction box position is compatible with the machining operation, press START to continue, otherwise press STOP/RESET
PLC_9523 – Beware of the position of any aggregates loaded in the slot when the slots are down
PLC_9524 – WARNING: axis manual movements not allowed. Reset area safety device
PLC_9525 – WARNING: axis manual movements not allowed. Check collision with machine-side tool magazine
PLC_9526 – Lift/lower presetter tool lenght timeout
PLC_9527 –
PLC_9528 –
PLC_9529 –
PLC_9530 – Glue bowl temperature KO
PLC_9531 – Glue roller temperature KO
PLC_9532 – Error on the piston of the guide that connects the banding material container to the edgebander
PLC_9533 – The guide that connects the banding material container to the edgebander is not down. Cannot move the edgebander.
PLC_9534 – ATTENTION: OPERATOR CONSENT REQUIRED. Press CONTINUE in order to proceed.
PLC_9535 – ATTENTION: EDGEBANDING STRIP HEIGHT INCOHERENT WITH THE PANEL THICKNESS.
PLC_9536 – ERROR: selected a glue-magazine disabled.
PLC_9537 – ERROR: rotation of glue magazine selector not allowed.
PLC_9538 – ERROR: glue magazine incompatible with the type of glue selected.
PLC_9539 – Glue load from standard pellet magazine selected.
PLC_9540 – Glue load from pre-melter magazine selected.
PLC_9541 – Rapid jog movements not allowed with the edge-banding unit down
PLC_9542 – WARNING: EDGEBANDING STRIP ALMOST TERMINATED: (Banding material container; Edgebanding strip away; Threshold;Remainder)
PLC_9543 – INSUFFICIENT EDGEBANDING STRIP REMAINDER: press START, or STOP+RESET, to continue.
PLC_9544 – Edgebanding unit not up: reset required to bring it to the rest position
PLC_9545 – The indicated edgebanding strip is present in the banding material container tooling table, but there is no more left.
PLC_9546 – Magazine encoder opening/closing timeout
PLC_9547 – Command given in strip magazine to cut strip with shears, but it does not move
PLC_9548 – Timeout for rest command of shears
PLC_9549 – The strip specified is not in the tooling table of the strip magazine
PLC_9550 – Strip forwards compensation failed
PLC_9551 – Release timeout on edgebanding unit
PLC_9552 – Insufficient strip drawn
PLC_9553 – The requested strip length is shorter than the permitted minimum
PLC_9554 – MAGBORDI Table: restriction: “LungBMin > DistLama” not complied with
PLC_9555 – INSUFFICIENT AMOUNT OF EDGEBANDING STRIP for the NEXT EDGEBANDING OPERATION: (Banding material container; Edgebanding strip away; PQBR; Remainder)
PLC_9556 – Lamp power for strip heating not permitted: must be between 0 and 100
PLC_9557 – Simulation with spindle off active but edgebanding simulation not active
PLC_9558 – Eedgebanding simulation active, but simulation with spindle off not active
PLC_9559 – WARNING, edgebanding simulation active
PLC_9560 – DANGER:the spindles may be rotating, but they are not controlled. Do not touch the tools
PLC_9561 –
PLC_9562 –
PLC_9563 –
PLC_9564 –
PLC_9565 –
PLC_9566 –
PLC_9567 –
PLC_9568 –
PLC_9569 –
PLC_9570 –
PLC_9571 –
PLC_9572 –
PLC_9573 –
PLC_9574 –
PLC_9575 –
PLC_9576 –
PLC_9577 –
PLC_9578 –
PLC_9579 –
PLC_9580 –
PLC_9581 –
PLC_9582 – Error positioning encoder suction box (location, target, tolerance, axis)
PLC_9583 – Suction box not zero setting
PLC_9584 – TP suction box movement timeout
PLC_9585 – Boring machine suction box movement timeout
PLC_9586 – Sensors for piston moving granule loader up to edge-banding unit are both active
PLC_9587 – Granule loader has been commanded back, but is still forwards
PLC_9588 – Granule loader has been commanded back, but relevant sensor has not been triggered
PLC_9589 – Heat regulator error: invalid offset
PLC_9590 –
PLC_9591 – Timeout in movement of granule loader drawer to rest position
PLC_9592 –
PLC_9593 –
PLC_9594 –
PLC_9595 –
PLC_9596 –
PLC_9597 –
PLC_9598 –
PLC_9599 –
PLC_9600 –
PLC_9601 –
PLC_9602 –
PLC_9603 – Axis positioning to park the unit has ended, but the Y cam safety microswitch is active
PLC_9604 – Attention: glue stick almost finished in the magazine.
PLC_9605 – Warning: Glue magazine in error.
PLC_9606 – Warning: the thermoregulators might be off, the high temperature threshold might not be active or rotation of the glue roller might not be active
PLC_9607 –
PLC_9608 – Press reset slot to restore the granule loader to normal operation
PLC_9609 – Warning: the loader that provides the glue tank is empty (stick or granules finished).
PLC_9610 – Warning: the glue loader is in error.
PLC_9611 – Banding material container outfeed sensor active: cut banding material or tool up banding material container and if necessary remove banding material from edge-banding unit
PLC_9612 – Check that banding material lane contains banding maternal number
PLC_9613 – Check that banding material lane is free
PLC_9614 – The STRIP pusher remains open out of the tooling.
PLC_9615 – Warning: banding material finished in lane number
PLC_9616 –
PLC_9617 –
PLC_9618 –
PLC_9619 –
PLC_9620 –
PLC_9621 –
PLC_9622 –
PLC_9623 –
PLC_9624 –
PLC_9625 –
PLC_9626 –
PLC_9627 –
PLC_9628 –
PLC_9629 –
PLC_9630 –
PLC_9631 – Tool change impossible with deflector tooled up on electrospindle
PLC_9632 – Error during baffle loading/unloading operation
PLC_9633 – The tool-holder is disabled for the deflector change. Check the data item PU_xxx->AbilDefl
PLC_9634 – Operation impossible: manually remove the deflector from the electrospindle
PLC_9635 – The magazine is disabled for change with deflector
PLC_9636 – Deflector loading failed
PLC_9637 – Attempt to move a rotary axis not compatible with the presence of the deflector on the electrospindle. Press Stop-Reset
PLC_9638 – Incorrect environment requested to run cycle. Switch to AUTOMATIC
PLC_9639 – It’s possible to restart machining without restoring the machine; press one of the two area selection push buttons to continue.
PLC_9640 – Tool change impossible with the deflector tooled on the electrospindle as a result of the dimensions of the adjacent tool holders already tooled
PLC_9641 – The contactor of actvive spindle is not enabled
PLC_9642 –
PLC_9643 – Machine emergency: the stopped motor input is not displayed even if the inverter has no frequency
PLC_9644 – Inverter error signalled in table INVERTER STATUS (or NINVES timeout expired)
PLC_9645 – Deflector unloading operation failed. Check the tooling data
PLC_9646 – The deflector fitted on the TP is different to that requested
PLC_9647 –
PLC_9648 –
PLC_9649 – TP deflector sensor missing
PLC_9650 – Cannot load/unload a deflector using a tool change (Syntax error during PCUA programming)
PLC_9651 – Error on read/write chuck piston of the revolver type magazine
PLC_9652 – Set MANUAL environment to move machine axes.
PLC_9653 – Radio transmission thickness tracer: input not enabled.
PLC_9654 – Radio transmission thickness tracer: error:
PLC_9655 – Radio transmission thickness tracer: low battery signal level.
PLC_9656 – Radio transmission thickness tracer: warning
PLC_9657 – Radio transmission thickness tracer: this name does not exist in the table.
PLC_9658 – Radio transmission thickness tracer: this name does not exist.
PLC_9659 – Thickness tracing cycle failed
PLC_9660 – Press the pedal to continue
PLC_9661 – Cannot read-write the inverter parameters.
PLC_9662 – The inverter parameters table is either disabled or has an incorrect number of columns.
PLC_9663 – The machine is probably not on. Retry by setting the machine in emergency and then repowering.
PLC_9664 – Bands not down
PLC_9665 – Machine in spindle stopped mode. Try again after removing spindle stopped mode.
PLC_9666 – Curtain guards not down and slot not homed
PLC_9667 – Error on deflector pneumatic device
PLC_9668 – Error in the movement of the protection barriers
PLC_9669 –
PLC_9670 –
PLC_9671 –
PLC_9672 – Selection of hood position not possible because TP has not been enabled by program or TP is already active in a tool change cycle
PLC_9673 –
PLC_9674 –
PLC_9675 –
PLC_9676 – Vacuum pump selector input altered. Reposition the selector and press START to continue.
PLC_9677 – START impossible: the origins required for a long panel have not been enabled in the program
PLC_9678 – Positioning has been requested for more than one carriage on the same mobile support
PLC_9679 – Simultaneous positioning of some mobile supports and some carriages has been requested
PLC_9680 – Request to position carriages or mobile supports: case not foreseen in commands received from ISO
PLC_9681 – At least two carriages belonging to different mobile supports have target positions that imply movements of different entity (each carriage must be moved by the same amount)
PLC_9682 – On a mobile support, the position programmed for a carriage means that it will hit an adjacent carriage
PLC_9683 –
PLC_9684 –
PLC_9685 –
PLC_9686 –
PLC_9687 –
PLC_9688 – No movement has been requested for any of the carriages
PLC_9689 – Emergency caused by opening safety fence or guard casing hatch. Check that the gates and casing hatch are closed.
PLC_9690 – Emergency circuit KO
PLC_9691 – Warning: the position programmed for a work table is the same as its current position. The movement has been cancelled
PLC_9692 –
PLC_9693 – Warning: dialogue with remote control panel failed
PLC_9694 – Warning: dialogue with software control panel failed
PLC_9695 –
PLC_9696 – Warning: axis selected on NC is not the one set from remote control panel
PLC_9697 – Warning: environment selected on NC is not the one set from remote control panel
PLC_9698 –
PLC_9699 –
PLC_9700 – Warning: the Tilting axis of the TP to be reset is not in the rest position
PLC_9701 – Warning: the rotating axis has been commanded during a tool change cycle
PLC_9702 – Warning: the position programmed for a carriage is the same as its current position. The movement has been cancelled. Carriage, table
PLC_9703 – Bad area configuration number
PLC_9704 – Warning: the contact controlled by the inverter stop security output is closed but the output is inactive
PLC_9705 – PLC Emergency: the inverter speed is 10% higher than the programmed speed or the motor stopped input is not ON within 10 seconds of the inverter stopping
PLC_9706 – Warning: motor stopped input is not active but inverter self-retain output is active. Check electrical connections
PLC_9707 – Warning: the TP might hit other parts of the machine. Press STOP-RESET to stop the program or continue using the command “Continue” on the remote control panel.
PLC_9708 – Warning: The electrospindle could collide with a part of the machine. Press STOP-RESET to interrupt the program or continue by using the Start button
PLC_9709 – Warning: the TP might hit other parts of the machine. Press STOP-RESET to stop the program or continue using the command “Disable” on the remote control panel to disable the collision control.
PLC_9710 – Warning: the spindle override is not at 100%. The tools will turn at a speed lower than the one programmed
PLC_9711 – Unable to activate the command. To activate the command, you must enable the remote console commands
PLC_9712 – A tool is present in a tool change magazine position for which the data item “Maximum length” (MAX_LUNG) has not been defined
PLC_9713 – In one of the positions in the tool change magazine there is an aggregate or deflector for which the data item “Additional Z corrector” (CORRSL) has not been defined
PLC_9714 – Unable to activate the command. To activate the command, you must disable the remote console commands
PLC_9715 –
PLC_9716 –
PLC_9717 – Warning: one or more overrides are not 100%
PLC_9718 – Guard between tables absent
PLC_9719 –
PLC_9720 –
PLC_9721 –
PLC_9722 –
PLC_9723 –
PLC_9724 –
PLC_9725 –
PLC_9726 –
PLC_9727 –
PLC_9728 –
PLC_9729 –
PLC_9730 –
PLC_9731 – Unloaders with bars not down
PLC_9732 –
PLC_9733 – Warning: possible colision between boring head and 5 axis head
PLC_9734 –
PLC_9735 – Axes of the 5-axis head not at rest.
PLC_9736 – Tracing cycle interrupted due to possible jolt.
PLC_9737 – The boring head is not in the rest position.
PLC_9738 – The protection barriers are not in the rest position.
PLC_9739 – Carriage not positioned on a table
PLC_9740 – Load tool from revolver magazine failed. Another load tool operation will be performed.
PLC_9741 –
PLC_9742 – Load tool from chain type magazine failed. Another load tool operation will be performed.
PLC_9743 – Data and selector of surfacing cycle are incongruent
PLC_9744 – The enabling selector of surfacing cycle has changed status
PLC_9745 – Check that the carriages involved in the “pack” reset are turned in a way that is compatible with this type of reset operation
PLC_9746 – Emergency due to inverter Overspeed
PLC_9747 –
PLC_9748 –
PLC_9749 –
PLC_9750 –
PLC_9751 – The cycle has been interrupted. If necessary, repeat the operation
PLC_9752 – Caution! The work table position is not corrected
PLC_9753 – Caution! The width of the panel is greater than the maximum width possible for the selected row of front stops
PLC_9754 – Unlocking has not been completed: keep the button pressed for longer
PLC_9755 – Caution! The tool used has exceeded the maximum distance to be travelled (Data item VITA_UT in the TOOL table)
PLC_9756 – Caution: EPS management not active in at least one of the working areas required by the program. The automatic work table tooling cycle will not be carried out
PLC_9757 – Caution: to complete activation of EPS management it is necessary to perform a global reset
PLC_9758 –
PLC_9759 –
PLC_9760 – Edgebanding material advance from magazine failed. Check both the optic fiber and the edge material tracks. Press STOP/RESET.
PLC_9761 –
PLC_9762 – Topping up of glue granules excluded by selector. Check the selector position on the electrical board.
PLC_9763 – Lift/lower banding material magazine cylinder sensors both active
PLC_9764 –
PLC_9765 –
PLC_9766 – Edgebander presser unit movement KO
PLC_9767 – Error: the presser unit is not in the position required by the program
PLC_9768 – Cutter waste does not fall down. Check the banding material container lead-out
PLC_9769 – Slot cannot be reset: fibre optic ON at banding material container lead-out.
PLC_9770 – Pressing roller hooked to the panel. Check the anti-hooking input.
PLC_9771 – Glue cannot be heated: reset the slots. Check that the edgeband unit is up.
PLC_9772 – Edgebanding strip not present underneath the fibre optic. Check the banding material container lead-out.
PLC_9773 – MANUAL EDGEBANDING STRIP LOADING: LOCK THE EDGEBANDING STRIP ON THE EDGEBAND UNIT. Press the pedal.
PLC_9774 –
PLC_9775 – HEATERS SAFETY TIMEOUT: in order to start the heaters again, disable and enable them via the selector.
PLC_9776 – MANUAL EDGEBANDING STRIP LOADING: PRESS THE PEDAL AGAIN TO REPOSITION THE EDGEBANDING STRIP ON THE EDGEBANDING UNIT.
PLC_9777 – MANUAL EDGEBANDING STRIP LOADING: RESET THE SWITCHING BOX OF THE CONTACT MATS TO START EDGEBANDING.
PLC_9778 – MANUAL EDGEBANDING STRIP LOADING: DEACTIVATE THE SELECTOR FOR MANUAL EDGEBANDING STRIP LOADING TO START EDGEBANDING.
PLC_9779 – MANUAL EDGEBANDING STRIP LOADING: ACTIVATE THE SELECTOR FOR MANUAL EDGEBANDING STRIP LOADING.
PLC_9780 – WARNING: THE MOTOR OF THE Rc-AXIS IS APPLYING AN EXCESSIVE TORQUE. LUBRICATE THE GLUE ROLLER. Press STOP+RESET.
PLC_9781 – WARNING: THE TEMPERATURE FOR TYPE 3 GLUE HAS BEEN SELECTED. Check the type of glue used.
PLC_9782 – WARNING: THE TEMPERATURE FOR EVA-TYPE GLUE HAS BEEN SELECTED. Check the type of glue used.
PLC_9783 – WARNING: THE TEMPERATURE FOR POLYURETHANE-TYPE GLUE HAS BEEN SELECTED. Check the type of glue used.
PLC_9784 – WARNING: GLUE TEMPERATURE PROTECTION ACTIVATED. Wait for cooling and select high threshold.
PLC_9785 – WARNING: AGGREGATE/BIT dimensions are too large to use the BLOWER on the electrospindle. Check the electrospindle tooling. Press STOP+RESET.
PLC_9786 – PHON down/up TIMEOUT: check the unit mechanics. Press STOP+RESET.
PLC_9787 – Glue cannot be heated: check for compressed air.
PLC_9788 – MANUAL EDGEBANDING STRIP LOADING: LENGTH OF THE EDGEBANDING STRIP TO BE LOADED MANUALLY (mm)=(length).
PLC_9789 – CLOSED RING CALIBRATION: TAKE OUT THE EDGEBANDING STRIP FROM THE EDGEBANDING DEVICE. Press STOP+RESET.
PLC_9790 – TAKE OUT THE EDGEBANDING STRIP FROM THE EDGEBANDING DEVICE. Press STOP+RESET.
PLC_9791 –
PLC_9792 – EDGEBANDING MATERIAL LOADING FROM MAG. 2 SUSPENDED: magazine occupied by the operator (check the status of the selector on the magazine)
PLC_9793 – STRIP END TOO LONG (OR TOO SHORT) NOT OUT OF THE MAGAZINE. Check the banding material container. Press STOP+RESET.
PLC_9794 – WARNING: THE INCLINED ROLLER WILL STAPLE THE EDGEBANDING STRIP ONLY WHEN IT IS STOPPED AND HAS REACHED THE BLADE LEVEL. Press KEY TO MODIFY.
PLC_9795 – WARNING: THE INCLINED ROLLER WILL STAPLE THE EDGEBANDING STRIP WHEN IT PASSES UNDER THE ROLLER. Press KEY TO MODIFY.
PLC_9796 –
PLC_9797 – CLOSED RING EXECUTION ENABLED WITHOUT TEST. Press KEY TO MODIFY. Extra edge (mm).
PLC_9798 – WARNING: TO EXECUTE THE PROGRAM PRESS THE START KEY.
PLC_9799 – WARNING: THE INCLINED ROLLER WILL NOT STAPLE THE EDGEBANDING STRIP ANY MORE. Press KEY TO MODIFY.
PLC_9800 – Tool measuring function not activated.
PLC_9801 –
PLC_9802 – Check via probe not carried out.
PLC_9803 –
PLC_9804 – Calculated value over dispersion tolerance limit.
PLC_9805 – Maximum value of tool diameter exceeded.
PLC_9806 – Maximum or minimum value of tool length exceeded.
PLC_9807 – Error in reading of a tool parameter.
PLC_9808 – Tool name not valid.
PLC_9809 – Beam error.
PLC_9810 – Spindle tab: Screw dowel position outside limits
PLC_9811 – Spindle tab: Coil disconnected
PLC_9812 – Error in LED supply voltage
PLC_9813 – Spindle tab: Communication error
PLC_9814 – Spindle tab: General error
PLC_9815 –
PLC_9816 – Measuring TP not enabled.
PLC_9817 –
PLC_9818 – At least one of the selected spindles is tooled with an aggregate.
PLC_9819 – Misalignment tolerance exceeded.
PLC_9820 – Hood command on tp with active ECS
PLC_9821 – ECS command with hoot not in park
PLC_9822 – ECS activation without float
PLC_9823 – Hoot automatic Position is not compatible with 5-axis head
PLC_9824 – Error: at least one of the selected spindles does not have a ECS axis
PLC_9825 – Error on an aggregate with automatic orientation: orientation out of tolerance. Press START to continue, press RESET to interrupt the cycle.
PLC_9826 – Cycle interrupted: it is necessary the zero setting of an aggregate with automatic orientation.
PLC_9827 – Timeout to wait for MT response.
PLC_9828 – The connection with the aggregate with automatic orientation to be moved is missing.
PLC_9829 – It is not possible to set the channel for the MT since the aggregate with automatic orientation is active. Unload the aggregate and try again.
PLC_9830 – It is not possible to set the channel for the aggregate with automatic orientation since no tilting aggregate has been loaded on the TP.
PLC_9831 – Error on an aggregate with automatic orientation: the subspindle has moved without being commanded to.
PLC_9832 – Warning: an aggregate with automatic orientation has been left on a TP with the machine off. The battery of the aggregate wastes energy.
PLC_9833 – Error in the movement of the piston of the rotating head subspindle.
PLC_9834 – Rotating borer subspindles down. Request a slot reset.
PLC_9835 –
PLC_9836 –
PLC_9837 –
PLC_9838 –
PLC_9839 –
PLC_9840 – The selected origin is off
PLC_9841 – Insufficient level password for the required function
PLC_9842 –
PLC_9843 –
PLC_9844 –
PLC_9845 –
PLC_9846 –
PLC_9847 –
PLC_9848 –
PLC_9849 –
PLC_9850 –
PLC_9851 – Supervisor activated
PLC_9852 – Error in supervisor protocol
PLC_9853 – Error in writing machining list
PLC_9854 – Supervisor error: machining list not activated
PLC_9855 – Supervisor error: machining list not empty
PLC_9856 – It is not possible to use manual discharge and automatic loading at the same time.
PLC_9857 – Timeout in supervisor comunication
PLC_9858 – Supervisor error: loading type or position in stock remains are not defined
PLC_9859 – Machining list not activated
PLC_9860 – Machining list empty
PLC_9861 – The automatic loading of stack is running
PLC_9862 – Waiting for loading protocol end
PLC_9863 – Inverter of loading pallet not ready
PLC_9864 – Warning: input of stack entrance on pallet active
PLC_9865 – Warning: inverter of loading pallet not up to speed
PLC_9866 – Warning: stack loading on loading pallet suspended
PLC_9867 – Input of panel presence not activated
PLC_9868 – Machinery and charger in interference
PLC_9869 – Stack load and stop inputs not defined, or both active
PLC_9870 – Starting parameters and type of automatic loading are not congruent
PLC_9871 – Error on vertical release of pre-load chains
PLC_9872 – Error on pneumatic stack lifting.
PLC_9873 – Attention: the outfeed panel safety photocell must be activated in order to reset the machine
PLC_9874 – Attention: set the emergency mode, then active the outfeed panel safety photocell in order to reset the machine
PLC_9875 – Safety microswitch of loading/unloading arm pressed.
PLC_9876 – Warning: HOLD has been requested
PLC_9877 – Machine in HOLD status
PLC_9878 – It is impossible to activate HOLD function
PLC_9879 – Door opening is enabled
PLC_9880 – Warning: door opening is requested
PLC_9881 – Warning: SEMIAUTOMATIC mode activated
PLC_9882 – Warning: Manual Unloading mode activated
PLC_9883 – Sweeper’s loadeing suction cup not active
PLC_9884 – Access door open or access request active
PLC_9885 – Front references input timeout.
PLC_9886 – System bistable solenoid valve control timeout. Inputs (E and R)
PLC_9887 – Machine suspension caused by outfeed panel safety
PLC_9888 – Error in moving read/write head piston of tool change type magazine
PLC_9889 – Error in general Panel Cell data
PLC_9890 – Error in the data of a Panel Cell loading pallet
PLC_9891 – Error in the data of a Panel Cell expelling arm
PLC_9892 – Error in the data of a Panel Cell unloading pallet
PLC_9893 – The CN has refused a request of movement of a group of axes from PLC
PLC_9894 – Error in the labelling data
PLC_9895 – MANUAL environment selection: it could be necessary to press in sequence STOP and RESET buttons.
PLC_9896 – Scissor lift not in down position. Roller bed manual movement not allowed
PLC_9897 – Stops down input timeout
PLC_9898 – Last roller presser hooking input of witch it is possible to remove the control. Execute a roller presser parking as soon as possible
PLC_9899 – Tool change interrupted because pressure too low during tool unloading
PLC_9900 – Reference message for Biesse Service
PLC_9901 – The rotating axis of a lowered working unit is not reset: to restore the unit perform SINGLE RESET of the Z axis followed by SINGLE RESET of this rotating axis
PLC_9902 – Axis blocked because of a hooking input of the roller presser disabled. Press the parking roller presser button to continue, otherwise press STOP-RESET buttons
PLC_9903 – A module on the field bus has not been detected
PLC_9904 – Error in the surfacing cycle: the number of enabled spindles is not 1.
PLC_9905 – Reached the minimum number of roller presser hooked inputs to control: it is not possible to erase the control. Execute a roller presser parking
PLC_9906 – Error in the surfacing cycle: tool used is an aggregate type of tool.
PLC_9907 – Error in the surfacing cycle: the working depth is exceeding the one authorized.
PLC_9908 – Roller presser release piston input not active
PLC_9909 – Error: possible interference between rack magazine and edgebander
PLC_9910 – The sensor of the piston spindle is not working properly
PLC_9911 – Slides positioned outside range
PLC_9912 – Incorrect environment requested to run operation. Switch to MANUAL
PLC_9913 – The tool is locked on the electrospindle, but the piston is not retracted
PLC_9914 – The tool is unlocked on the electrospindle, but the piston is not out
PLC_9915 – Override decrease due to the inverter current exceeding the trigger threshold
PLC_9916 – The TP position is not in the permitted working position
PLC_9917 – The boring machine position is not in the permitted working position
PLC_9918 – Axis operation feed timeout
PLC_9919 – The automatic reset of a magazine can not be carried out because some axes are not reset. Manually reset the TP
PLC_9920 – The requested position for the TP is not in the permitted position
PLC_9921 – The requested position for the boring machine is not in the permitted position
PLC_9922 – The requested position for the TP suction box is not in the permitted position
PLC_9923 – The requested position for the boring machine suction box is not in the permitted position
PLC_9924 – The command requested on a TP object is invalid
PLC_9925 – The float of the TP is not idle or the float blower is on
PLC_9926 – The TP cleaning blower is on
PLC_9927 – Boring machine cooler not functioning or off
PLC_9928 – There are spindles with and without inverters amongst the selected spindles
PLC_9929 – An axis movement has been requested beyond the upper limit switch software
PLC_9930 – An axis movement has been requested beyond the lower limit switch software
PLC_9931 – OVERSPD signal value incorrect
PLC_9932 – The M3 spindle on instruction has not been programmed
PLC_9933 – End of program without M5
PLC_9934 – The PTRZ or has not been programmed or the correction value is out of range
PLC_9935 – Inverter engagement timeout: not all inverters required for the selected spindles are free. Check that the last process complete finished with a spindle off instruction
PLC_9936 – Spindles not selected timeout: some non selected spindles are not idle. Check that the last process complete finished with a spindle idle instruction
PLC_9937 – The tool change cycle magazine is not compatible with the program execution centre
PLC_9938 – The safety button on the remote console are pressed for too long:The related electrical contact may be defective
PLC_9939 – Warning: the boring machine could collide against a part of machine. Press STOP-RESET to interrupt the program or carry on using the “Continue” command on the remote console.
PLC_9940 – Warning: the boring machine could collide against a part of machine. Press STOP-RESET to interrupt the program or carry on using the “Deactivate” command on the remote console to deactivate the collision control.
PLC_9941 – Warning: stack height reading limit switch pressed
PLC_9942 – Warning: X pushing photocell activated
PLC_9943 – Warning: Y pushing sensor activated
PLC_9944 – Error in the “Spindles disabled” data of the tool holder
PLC_9945 – Spindle disabled for tool change
PLC_9946 – Loading pallet calibration in course
PLC_9947 – Cannot disconnect tool because the slot does not rise properly
PLC_9948 – Impossible to activate or deactivate the piece release from the pedal/selector/remote console.
PLC_9949 – The TP blower tool blow is active
PLC_9950 – Pushing failed. Error during panel pushing with the horizontal piston on the loading pallet
PLC_9951 – Warning! The Y panel dimension (LPY) maximum allowed not set
PLC_9952 – Loading pallet movement KO. The pallet is on the UP sensor
PLC_9953 – Warning, the CUT magazine cannot be restored due to the presence of the deflector
PLC_9954 – Machine emergency: stack height reading not possible
PLC_9955 – Loading pallet movement KO. Error code:
PLC_9956 – Disabling of unloading pallet sweeping command
PLC_9957 – Expected input not enabled
PLC_9958 – Front references input timeout
PLC_9959 – Unloading table-piece presence micro collision
PLC_9960 – Maximum allowed pile height exceeded
PLC_9961 – Nesting Cell enabling selector shifted
PLC_9962 – Nesting Cell disabled or command in progress
PLC_9963 – Invalid work origin number for executing a program with active Nesting Cell
PLC_9964 – No power to machine
PLC_9965 – No pieces in the Nesting Cell loader
PLC_9966 – Incorrect position of head components (cup or pushing device)
PLC_9967 – Expected input not enabled
PLC_9968 – Nesting Cell pistons not reset
PLC_9969 – Enter data and press the start button
PLC_9970 – Cycle cannot be started unless key for entering Nesting Cell parameters is pressed or with wrong parameters
PLC_9971 – Number of machined panels equal to number set
PLC_9972 – Not valid operation: vacuum forcing active
PLC_9973 – Not enough vacuum in the machine area closest to the Nesting Cell work origin
PLC_9974 – Work list ends
PLC_9975 – Axes not reset
PLC_9976 – Pallet panel pusher not homed
PLC_9977 – Piece positioning photocell shadowed
PLC_9978 – Enabling signal waiting time at unloading
PLC_9979 – Loading cycle error: piece presence microswitch pressed
PLC_9980 – Axis simulated from NC: the axis is unusable
PLC_9981 – Piece positioning input waiting time
PLC_9982 – Pieces thickness exceeds the maximum value permitted for multiple load
PLC_9983 – Piece not locked by cups
PLC_9984 – The pushers along Y are not in the correct position according to panel sizes
PLC_9985 – Pile height:
PLC_9986 – Axis at the UP hardware limit switch
PLC_9987 – Axis at the DOWN hardware limit switch
PLC_9988 – Disabling of loading pallet sweeping command
PLC_9989 – Pneumatic multifunction unit positioning timeout
PLC_9990 – A tool is present in a position in the belt magazine for which the “Maximum length” (MAX_LUNG) data has not been defined
PLC_9991 – An aggregate or deflector is present in a position in the belt magazine for which the “additional corrector in Z” (CORRSL) data has not been defined
PLC_9992 – A tool is present in a position in the revolver magazine for which the “Maximum length” (MAX_LUNG) data has not been defined
PLC_9993 – An aggregate or deflector is present in a position in the revolver magazine for which the “Z additive calibrator” data has not been defined
PLC_9994 – The selection of the single origin and the row are not in accordance
PLC_9995 – The suspension cycle on the bench can not be reset
PLC_9996 – PLC emergency
PLC_9997 – The UNICLAMP selector switch is inconsistent with the PUNI program parameter. Press STOP-RESET and turn the UNICLAMP selector switch to the correct position
PLC_9998 – The TP deflector is not shown as present in the table TAB_DEF (dato DeflPres)
PLC_9999 – TP deflector equipping data error: the deflector is present on the magazine and the TP
PLC_90000 – Invalid origin for start
PLC_90001 – Piece loading/unloading automatic cycle active, but locking mode with uniclamp devices not active
PLC_90002 – Piece loading error: check photocell
PLC_90003 – Error in the automatic piece loading cycle
PLC_90004 – Program without the definition of the work table tooling
PLC_90005 – Transfer positioning error: check photocell
PLC_90006 – Incorrect piece loading control: remove the piece from the roller bed loading station and press the button for piece backward movement
PLC_90007 – Error in the automatic piece unloading cycle
PLC_90008 – Piece unloading error: check photocell
PLC_90009 – Piece automatic cycle: error in the movement of front stops
PLC_90010 – Piece automatic cycle: error in the movement of the rear stops
PLC_90011 – Automatic piece cycle: error in movement of blade to lift the piece being loaded
PLC_90012 – Piece automatic cycle: error in the reading of piece data from the logical centre
PLC_90013 – Piece automatic cycle: the thickness of a piece exceeds the thickness set in the program parameters
PLC_90014 – An exchange cycle of uniclamp devices with mechanical hand and automatic cycle not active has been programmed
PLC_90015 – Error in the program: the ISO step locking cycle (e.g. PCUA) has not been programmed
PLC_90016 – Piece automatic cycle: error in the movement of the fixed gripper
PLC_90017 – Piece automatic cycle: error in the movement of the moving gripper
PLC_90018 – Piece automatic cycle: piece not locked with the fixed gripper
PLC_90019 – Piece automatic cycle: piece not locked with the moving gripper
PLC_90020 – Piece automatic unloading: error in the lifter movement
PLC_90021 – Piece automatic unloading: the lifter cannot descend because the input photocell is not empty
PLC_90022 – Piece automatic cycle: the overlimit sensor of the fixed gripper has been enabled
PLC_90023 – Piece automatic cycle: the overlimit sensor of the moving gripper has been enabled
PLC_90024 – Piece automatic cycle: the piece length is not within tolerance (Value , size , tolerance)
PLC_90025 – Piece automatic cycle: the piece width is not within tolerance (Value , size , tolerance)
PLC_90026 – Piece automatic cycle: the piece thickness is not within tolerance
PLC_90027 – Cannot find a position of the moving gripper not colliding with the load transfer belts
PLC_90028 – Cannot find a position of the moving gripper not colliding with the uniclamp devices
PLC_90029 – Cannot find a position of the moving gripper not colliding with the hooks of the lifter
PLC_90030 – Error in the uniclamp device exchange cycle of the piece
PLC_90031 – The vertical axis of a gripper is not homed
PLC_90032 – Exchange cycle of uniclamp devices: the grippers cannot be positioned
PLC_90033 – The uniclamp device position more to the right is not compatible with the fixed gripper position
PLC_90034 – Cycle or command incompatible with the piece automatic cycle
PLC_90035 – Piece automatic cycle: the vertical axis of a gripper is down and the X-axis is commanded
PLC_90036 – No piece automatic cycle is running, but the vertical axis of a gripper is down
PLC_90037 – Piece automatic cycle: at least one Uniclamp device necessary for a piece is already used
PLC_90038 – Nail magazine empty. Add nails to the magazine. End this operation by pressing the gun deactivation key twice
PLC_90039 – Nail positions incorrect
PLC_90040 – Vice exchange cycle with master controller not possible
PLC_90041 – Inkjet printer not ready
PLC_90042 – Inkjet printer error
PLC_90043 – Error in the the Inkjet printhead movement
PLC_90044 – Radio transmission thickness tracer: no battery signal
PLC_90045 – Radio transmission thickness tracer: input not enabled
PLC_90046 – Radio transmission thickness tracer: error:
PLC_90047 – Radio transmission thickness tracer: low battery signal level
PLC_90048 – Radio transmission thickness tracer: warning
PLC_90049 – Radio transmission thickness tracer: this name does not exist in the table
PLC_90050 – Radio transmission thickness tracer: this name does not exist
PLC_90051 – Thickness tracing cycle failed
PLC_90052 – Scheduled maintenance: maintenance operations on the TP are necessary
PLC_90053 – Scheduled maintenance: maintenance operations on the vacuum pump are necessary
PLC_90054 – Scheduled maintenance: maintenance operations on the boring machine are necessary
PLC_90055 – Scheduled maintenance: expired programmed maintenance times reset
PLC_90056 – Error in movement of Dw Up applicator
PLC_90057 – Number of remaining labels lower than minimum value. Replace the roll and reset the counter
PLC_90058 – Length of remaining ribbon lower than minimum value. Replace the ribbon and reset the counter. The ribbon is sufficient for no. of labels:
PLC_90059 – Press the Start programs button to continue without performing the measurement of the piece length
PLC_90060 – Tool lubrification: low oil level
PLC_90061 – Input not active
PLC_90062 – PLC Emergency: Emergency for energetic saving (GREEN function)
PLC_90063 – Press the program start button to continue
PLC_90064 – Presetting piston movement error.
PLC_90065 – Presetting is not in the rest position.
PLC_90066 – The measuring tool device is not ready (par1=input).
PLC_90067 – Energetic saving actived (GREEN function)
PLC_90068 – Inkjet printer write device: safety sensor not active
PLC_90069 – Warning: in order to complete the release cycle, all the zones must be enabled
PLC_90070 – Manually remove the piece with wrong dimensions and press the piece recall button to restart the cycle
PLC_90071 – Automatic cycle: the position for the fixed collet is further to the right than the right side of the piece
PLC_90072 – Automatic piece cycle: piece unloading area occupied
PLC_90073 – Piece unload cycle: error in the marking data items of a piece
PLC_90074 – Error in the marking cycle of a piece
PLC_90075 – Release the button to activate the compressed air
PLC_90076 – Release the button to start the shutdown and compressed air deactivation cycle
PLC_90077 – Collision between the piece and a clamp (table, carriage)
PLC_90078 – Piece automatic cycle: a piece thickness is larger than the max. thickness allowed
PLC_90079 – A tool is present inside the magazine on board the machine for which the “Maximum length” (MAX_LUNG) datum has not been set
PLC_90080 – In one of the positions in the revolver magazine there is an aggregate or deflector for which the data item “Additional Z corrector” (CORRSL) has not been defined
PLC_90081 – Warning: piece locking is not active in that the zone selectors are all OFF
PLC_90082 – Error in the movement of the fixed suction cup of the thin panels kit
PLC_90083 – Error in the movement of the movable suction cup of the thin panels kit
PLC_90084 – Error in the vacuum activation of the fixed suction cup of the thin panels kit
PLC_90085 – Error in the vacuum activation of the movable suction cup of the thin panels kit
PLC_90086 – Error while communicating with the NC of the Multilevel magazine
PLC_90087 – Thickness tracer laser: error
PLC_90088 – Piece automatic unloading: the lifter cannot descend because the output photocell is not empty
PLC_90089 – Error barcode timeout , PRESS the button Load to try again
PLC_90090 – It is not possible to find a position in which the mobile clamp does not collide with the rollers
PLC_90091 – It is not possible to find a position in which the fixed clamp does not collide with the rollers
PLC_90092 – Clamp opening error
PLC_90093 – Clamp closing error
PLC_90094 – Pieces not aligned in X
PLC_90095 – Loading pallet lowering to deactivate the feeding of the stack in position
PLC_90096 – Activation of the loading pallet safety micro
PLC_90097 – Error when moving the loading pallet encoder
PLC_90098 – Automatic piece cycle: loading or unloading order incorrect
PLC_90099 – Impossible to move the scissors: move the Xc-axis to a position higher than the non-interference position
PLC_90100 – Error in the “slave” field
PLC_90101 – Error: M41 not programmed
PLC_90102 – Error in the movement of the vertical piston 1 of the sweeping
PLC_90103 – Error in the movement of the vertical piston 2 of the sweeping
PLC_90104 – Error in the sweeping manifold movement
PLC_90105 – Error in the movement of the suction cup-pushing device unit of the sweeping
PLC_90106 – Error in the activation of the sweeping suction cup vacuum
PLC_90107 – Error in the movement of the sweeping pushing device
PLC_90108 – Error in the movement of unloading pallet type 1
PLC_90109 – Error in the movement of the piece pusher of the loading pallet type 1
PLC_90110 – Error in the movement of the stack pressure piston of the loading pallet type 1
PLC_90111 – Error in the stack reading piston of the loading pallet type 1
PLC_90112 – Error in the movement of the x pusher of the loading pallet type 1
PLC_90113 – Error in the movement of the Y pusher of the loading pallet type 1
PLC_90114 – Sweeping disabling input active
PLC_90115 – Incorrect sweeping movement sequence
PLC_90116 – Panel Cell loading pallet disabled
PLC_90117 – Panel cell unloading pallet disabled
PLC_90118 – Panel Cell pistons not reset
PLC_90119 – Cannot reset the Panel cell. Move the axes up to their home position
PLC_90120 – Cannot move the axes: move the Xc axis up to the positive software limit switch or to a position lower than home position
PLC_90121 – Unloading pallet not defined
PLC_90122 – Sweeping axis direction and unloading pallet position not congruent
PLC_90123 – Panel unloading blocked due to non-functioning roller mat
PLC_90124 – Roller mat stop photocell occupied: to continue unloading, free the photocell and press unloading consent
PLC_90125 – Number of loaded panels equal to number set
PLC_90126 – Panels with different thickness cannot be loaded-unloaded: they must be first unloaded and then loaded
PLC_90127 – End of automatic cycle
PLC_90128 – WARNING: override is at 100%
PLC_90129 – The two-hands control buttons have been released
PLC_90130 – Enabling push buttons of two-hands control
PLC_90131 – The two-hands control buttons are active at the same time
PLC_90132 – The two-hand control buttons are not activated in the maximum time
PLC_90133 – Release both buttons of the two-hands control
PLC_90134 – Error in the movement of the Y horizontal pusher of the loading pallet type 2
PLC_90135 – Error in the movement of the Y vertical pusher of the loading pallet
PLC_90136 – Error in activation of vacuum on suction cups of Y pusher of type 2 loading pallet
PLC_90137 – Time-out for Piece List graphic interface
PLC_90138 – Deflector error
PLC_90139 – Labelling disabled or program in progress
PLC_90140 – Step by Step simulation: press the start button to continue
PLC_90141 – Label printer not ready
PLC_90142 – Printed label not picked up by applicator. Check the printer parameter values are correct
PLC_90143 – No labels for printing
PLC_90144 – Number of label pick-up or application attempts exceeded
PLC_90145 – Label applicator not up. Press the applicator reset button
PLC_90146 – Failed command on label applicator
PLC_90147 – The TP deflector magazine position is occupied with another object
PLC_90148 – Communication error on the Inkjet serial line
PLC_90149 – ACK Inkjet response timeout error
PLC_90150 – Movement of one axis impossible
PLC_90151 – Cannot move the axis: move the Xc axis to a position higher than the idle position
PLC_90152 – Impossible to start the load cycle for more than one panel with the air cushion surface selected.
PLC_90153 – Error when moving the suction cup device unit of the sweeping arm
PLC_90154 – Roller belt movement stop photocells not configured
PLC_90155 – Roller belt movement stop photocell not working
PLC_90156 – Impossible to start the load cycle for more than one panel with unloading pallet 2 selected
PLC_90157 – Suspension for photocells engaged and suspension position exceeded
PLC_90158 – The input for pile detected is not defined
PLC_90159 – Machine in suspension. The tool tooled on the TP has a length greater than the data value written in TP->MaxUtSca
PLC_90160 – The selector keeps the uniclamps closed: to continue, disable the selector
PLC_90161 – Undefined uniclamp vice
PLC_90162 – Warning: possible collision of the piece with a vice in the length measuring cycle
PLC_90163 – The state of the selector called automatic/manual loading cycle, has been changed
PLC_90164 – Piece automatic loading: piece too short
PLC_90165 – Piece automatic cycle: a piece parameter for one of the fixed cycles GCARICO, GSCARICO o GSCAMBIO has not been defined
PLC_90166 – Piece automatic cycle: the piece data are not defined in the program (through the GDESCPEZZO)
PLC_90167 – Error in the definition of at least one symmetrical spindle
PLC_90168 – PZON parameter incorrect: the work table cannot belong to the indicated area
PLC_90169 – Machine in suspension from the loading pallet
PLC_90170 – Error for loading pannel in loading pallet
PLC_90171 – Error on an aggregate with automatic orientation: 1=communication error, 2=error in the aggregate data, 3=TP without an aggregate with automatic orientation.
PLC_90172 – The battery on the aggregate with automatic orientation is almost discharged. Replace the battery.
PLC_90173 – Error on an aggregate with automatic orientation: the subspindle does not move or moves discontinuously. It could be an RF communication problem between the aggregate and the NC or a mechanical failure when the subspindle moves. The aggregate angle could not match with the encoder position.
PLC_90174 – Waiting for consent to load panel
PLC_90175 – Last panel to load
PLC_90176 – Waiting for consent to load panel reset
PLC_90177 – Electrospindle fan rotation KO
PLC_90178 – Impossible to load deflector
PLC_90179 – Error in the movement of the x pusher of the loading pallet type 2
PLC_90180 – Warning: a strip may still be attached to the nail gun
PLC_90181 – Alarm on module on an electrospindle bus
PLC_90182 – Error on module on an electrospindle bus
PLC_90183 – Error when activating the piston vacuum for the loading pallet pusher along X
PLC_90184 – Unloading pallet not reset
PLC_90185 – Error in the movement of the roller presser vertical pistons
PLC_90186 – Error in the movement of the roller presser release pistons
PLC_90187 – Error in the movement of the roller presser parking unit pistons
PLC_90188 – Roller not on the presser
PLC_90189 – Error in presser roller detection
PLC_90190 – Step-by-step simulation: press Start
PLC_90191 – The roller presser is not compatible with the program execution centre
PLC_90192 – The roller presser is in the pick-up or parking phase
PLC_90193 – Warning: the roller presser is on the machine but the slot is not enabled for its use. Park the roller presser
PLC_90194 – Error in the movement of the roller presser cover pistons
PLC_90195 – DANGER: an electrospindle is rotating, but is not controlled. Do not touch the tool
PLC_90196 – Loading pallet not reset
PLC_90197 – Sweeping arm not reset
PLC_90198 – The maximum tool diameter allowed with the roller presser has been exceeded
PLC_90199 – Warning: the roller presser is on the machine
PLC_90200 – Error in work cycle: the tool being used is not allowed with the roller presser
PLC_90201 – Error in work cycle: roller presser position outside panel. Axis blocked.
PLC_90202 – Axis blocked due to interference with roller presser.
PLC_90203 – Error in work cycle: roller presser used in the program but not activated
PLC_90204 – Error in the movement of unloading pallet type 2
PLC_90205 – Error in the movement of the x pusher of the loading pallet type 4
PLC_90206 – Error in the movement of the Y pusher of the loading pallet type 4
PLC_90207 – Error when moving the label rotation piston
PLC_90208 – Warning: spindle unusable. Electrospindle KO control board input
PLC_90209 – Error when moving the parking unit horizontal piston of the roller presser
PLC_90210 – GLUE ROLLER IN TEMPERATURE AND IN ROTATION. TO CONTINUE, PRESS START.
PLC_90211 – WAITING TIME FOR GLUE ROLLER IN TEMPERATURE AND IN ROTATION. EDGE LOAD ON EDGEBANDING SUSPENDED.
PLC_90212 – Warning: the edgebanding track will open after gripping start.
PLC_90213 – Warning: the edgebanding track will open after gripping end.
PLC_90214 – Warning: glue roller in temperature but the selector does not enable the rotation. Risk of burning the glue.
PLC_90215 – Error: Blower not active or not present
PLC_90216 – WARNING: Closed Ring Sensor still active, clean the sensor
PLC_90217 –
PLC_90218 –
PLC_90219 –
PLC_90220 –
PLC_90221 – WARNING: a temperature SetPoint has been set which exceeds the scale limit
PLC_90222 – DELAY TIME FOR GLUE ROLLER TEMPERATURE: discharge pipe not at the correct temperature
PLC_90223 – PRECUTTING CYCLE KO: CHECK: EDGEBANDING DEVICE ENABLED, AXES ZERO-SET, SLOT RESET, NC IN MANUAL MODE
PLC_90224 – PRECUTTING CYCLE: PRESS START TO PROCEED WITH THE CYCLE
PLC_90225 – PRECUTTING CYCLE: EDGE PRECUTTING LENGTH SET (mm)=(length)
PLC_90226 – PRE-HEATING KO: NC NOT MANUAL(2) NC ACTIVE(4) AXES NOT ZERO-SET(8) SLOTS NOT RESET(16) PROG ACTIVE(32)
PLC_90227 – Program Maintenance: maintenance operations are required on the Glue Roller
PLC_90228 – GLUE BOWL: possible malfunction of the presence sensor glue, run glue load.
PLC_90229 – GLUE BOWL: possible malfunction of the presence sensor glue or box of glue is empty
PLC_90230 – It is necessary to zero-set the Cb axis, it’s out of range.
PLC_90231 –
PLC_90232 –
PLC_90233 –
PLC_90234 –
PLC_90235 –
PLC_90236 –
PLC_90237 –
PLC_90238 –
PLC_90239 –
PLC_90240 –
PLC_90241 –
PLC_90242 –
PLC_90243 –
PLC_90244 –
PLC_90245 –
PLC_90246 –
PLC_90247 –
PLC_90248 –
PLC_90249 –
PLC_90250 –
PLC_90251 –
PLC_90252 –
PLC_90253 –
PLC_90254 –
PLC_90255 –
PLC_90256 –
PLC_90257 –
PLC_90258 –
PLC_90259 –
PLC_90260 –
PLC_90261 –
PLC_90262 –
PLC_90263 –
PLC_90264 –
PLC_90265 –
PLC_90266 –
PLC_90267 –
PLC_90268 –
PLC_90269 –
PLC_90270 –
PLC_90271 –
PLC_90272 –
PLC_90273 –
PLC_90274 –
PLC_90275 –
PLC_90276 –
PLC_90277 –
PLC_90278 –
PLC_90279 –
PLC_90280 –
PLC_90281 –
PLC_90282 –
PLC_90283 –
PLC_90284 –
PLC_90285 –
PLC_90286 –
PLC_90287 –
PLC_90288 –
PLC_90289 –
PLC_90290 –
PLC_90291 –
PLC_90292 –
PLC_90293 –
PLC_90294 –
PLC_90295 –
PLC_90296 –
PLC_90297 –
PLC_90298 –
PLC_90299 –
PLC_90300 –
PLC_90301 –
PLC_90302 –
PLC_90303 –
PLC_90304 –
PLC_90305 –
PLC_90306 –
PLC_90307 –
PLC_90308 –
PLC_90309 –
PLC_90310 –
PLC_90311 –
PLC_90312 –
PLC_90313 –
PLC_90314 –
PLC_90315 –
PLC_90316 –
PLC_90317 –
PLC_90318 –
PLC_90319 –
PLC_90320 –
PLC_90321 –
PLC_90322 –
PLC_90323 –
PLC_90324 –
PLC_90325 –
PLC_90326 –
PLC_90327 –
PLC_90328 –
PLC_90329 –
PLC_90330 –
PLC_90331 –
PLC_90332 –
PLC_90333 –
PLC_90334 –
PLC_90335 –
PLC_90336 –
PLC_90337 –
PLC_90338 –
PLC_90339 –
PLC_90340 –
PLC_90341 –
PLC_90342 –
PLC_90343 –
PLC_90344 –
PLC_90345 –
PLC_90346 –
PLC_90347 –
PLC_90348 –
PLC_90349 –
PLC_90350 –
PLC_90351 –
PLC_90352 –
PLC_90353 –
PLC_90354 –
PLC_90355 –
PLC_90356 –
PLC_90357 –
PLC_90358 –
PLC_90359 –
PLC_90360 –
PLC_90361 –
PLC_90362 –
PLC_90363 –
PLC_90364 –
PLC_90365 –
PLC_90366 –
PLC_90367 –
PLC_90368 –
PLC_90369 –
PLC_90370 –
PLC_90371 –
PLC_90372 –
PLC_90373 –
PLC_90374 –
PLC_90375 –
PLC_90376 –
PLC_90377 –
PLC_90378 –
PLC_90379 –
PLC_90380 –
PLC_90381 –
PLC_90382 –
PLC_90383 –
PLC_90384 –
PLC_90385 –
PLC_90386 –
PLC_90387 –
PLC_90388 –
PLC_90389 –
PLC_90390 – The door is open
PLC_90391 – Automatic piece cycle: error while moving the right clamp
PLC_90392 – Automatic piece cycle: piece not locked by right clamp
PLC_90393 – Automatic piece cycle: the overlimit sensor for the right clamp is active
PLC_90394 – Closing timeout clamp
PLC_90395 – Error grip thickness (workpiece thickness; measured thickness; tolerance)
PLC_90396 – Opening timeout clamp
PLC_90397 – Open door request
PLC_90398 – Error in the movement of the load protection forward / reverse
PLC_90399 – Suspension due to spindle enabled but not working
PLC_90400 –
PLC_90401 –
PLC_90402 –
PLC_90403 – Wait protection cabin closed
PLC_90404 –
PLC_90405 –
PLC_90406 –
PLC_90407 –
PLC_90408 –
PLC_90409 –
PLC_90410 –
PLC_90411 –
PLC_90412 –
PLC_90413 –
PLC_90414 –
PLC_90415 –
PLC_90416 –
PLC_90417 –
PLC_90418 –
PLC_90419 –
PLC_90420 –
PLC_90421 – Working cycle error: roller presser vertical pistons not in a rest position
PLC_90422 – Error: not all roller presser vertical pistons are raised
PLC_90423 –
PLC_90424 – The reset of the vertical axis of the TP is not possible, because its rotational axis is not at rest
PLC_90425 – Axis not in rest position
PLC_90426 –
PLC_90427 –
PLC_90428 – Error: it’s not possible to change the state of a switch/button
PLC_90429 – Suction system KO
PLC_90430 – Active surveillance SMS
PLC_90431 – Working cycle error: the TP presser is commanded and the roller presser is present in machine
PLC_90432 – Program execution consent by roller presser is not active
PLC_90433 –
PLC_90434 –
PLC_90435 –
PLC_90436 –
PLC_90437 – Error on printer
PLC_90438 –
PLC_90439 –
PLC_90440 –
PLC_90441 –
PLC_90442 –
PLC_90443 –
PLC_90444 – Axis blocked because of a release input of the roller presser disabled
PLC_90445 – Pre-alarm for high temperature on TP stator
PLC_90446 – Alarm for high temperature on TP stator
PLC_90447 – Before using the TP, it is necessary to perform a warm-up cycle
PLC_90448 – Pre-alarm for high temperature on TP bearings
PLC_90449 – Alarm for high temperature on TP bearings
PLC_90450 – The tables or modules (switching boxes) of the safety system have not been configured correctly (SilNet and SilNode tables)
PLC_90451 – The modules (switching boxes) of the safety system are not working correctly
PLC_90452 – At least one module (switching box) of the safety system is not working correctly
PLC_90453 – Machine stoppage caused by pressure on the Bumper
PLC_90454 – Safety switching box. Machine emergency caused by the opening of the Emergency chain
PLC_90455 – Safety switching box. Overspeed signalled by PLC or Inverter
PLC_90456 – Safety switching box. Emergency on axis check safety tab. The tab has detected an anomaly in the slow speed or axis position check
PLC_90457 – Safety switching box. The position of the curtain guards or spindle is not correct while the spindle is rotating
PLC_90458 – Safety switching box. Contactor anomaly: General function contactors or Gate release contactors or Free area contactors or Contactors for managing the axis check safety tabs
PLC_90459 – Safety switching box. Additional mat triggered
PLC_90460 – Attention: the photocell barrier must be reset in order to reset the machine.
PLC_90461 – Safety switching box. Safety switching box in configuration.
PLC_90462 – Safety module. Attention: the spindle contactor is not activated but spindle rotation has been commanded (inverter 2)
PLC_90463 – Wait 10 seconds before trying to switch on the machine
PLC_90464 – Wait 10 seconds before trying to switch on the machine. When the switch-on button is pressed, the machine does not switch on because of errors on the general retro-activities
PLC_90465 – Safety switching box. Emergency caused by the PLC enabling output, that has switched to OFF
PLC_90466 – Safety switching box. Possible spindle rotation not controlled. The guards (doors) remain locked. Wait until the spindles have stopped, then deactivate and reactivate the tooling selector.
PLC_90467 – Emergency from PLC. The auxiliary stop button on the command console has been pressed.
PLC_90468 – Attention: the PLC debug option has been set on the safety switching box
PLC_90469 – Safety switching box. Attention: the spindle contactor is not activated but spindle rotation has been commanded
PLC_90470 – Safety switching box. The Overspeed output is not working correctly
PLC_90471 – Attention: an option has been set on the safety switching box but not on the PLC
PLC_90472 – Attention: an option has been set on the PLC but not on the safety switching box
PLC_90473 – Attention: set the emergency mode, then reset the photocell barrier in order to reset the machine.
PLC_90474 – The maximum speed of the X-axis has diminished because the mats, photocells or machine cab have not been configured
PLC_90475 – An interpolation speed limit has been set on the machine
PLC_90476 – The interpolation speed has been restored on the machine
PLC_90477 – Safety module. Inconsistency between options and status of the inputs detected by the safety switching box (1). Enter the option on the switching box, then switch the machine off and back on again.
PLC_90478 – Safety module. The safety switching box has not detected the mats or safety barrier
PLC_90479 – Machine suspension because the maximum interpolation speed has been exceeded in the program
PLC_90480 – It is not possible to command the inverter because the inverter is not powered.
PLC_90481 – Safety module. To restore the machine power may be necessary the reset of the safety fence
PLC_90482 – Safety module. Inconsistency between options and status of the inputs detected by the safety switching box (2). Enter the option on the switching box, then switch the machine off and back on again.
PLC_90483 – Safety module. Inconsistency between options and status of the inputs detected by the safety switching box (3). Enter the option on the switching box, then switch the machine off and back on again.
PLC_90484 – The zeroing of axes is not been completed
PLC_90485 – Emergency caused by the barrier of photocells because edging unit is not in the parking lot.
PLC_90486 – Command from user interface not executed
PLC_90487 – Fatal error on a vibrometer
PLC_90488 – Fatal error on the vibrometer of a TP
PLC_90489 – Overtemperature alarm on a vibrometer
PLC_90490 – Overtemperature alarm on the vibrometer of a TP
PLC_90491 – General error on a vibrometer
PLC_90492 – General error on the vibrometer of a TP
PLC_90493 – Collision alarm on a vibrometer
PLC_90494 – Collision alarm on TP
PLC_90495 – Vibration alarm on a vibrometer
PLC_90496 – Vibration alarm on TP
PLC_90497 – Pre-alarm for unbalanced tool on TP
PLC_90498 – Alarm for unbalanced tool on TP
PLC_90499 – Time-out on a vibrometer
PLC_90500 – The current is higher than threshold S6 for a time period longer than that allowed.
PLC_90501 – The tables and/or the carriages are not in the right position.The right position of the tables and/or of the carriages has been lost. Press STOP twice and launch the program again
PLC_90502 – WARNING: THE MOTOR OF THE BORING MACHINE IS STOPPED. Press STOP twice
PLC_90503 – WARNING: THE LUBRICATION OF THE BORING HEAD HAS BEEN REQUESTED. Press STOP twice
PLC_90504 – Forbidden position of the carriage side magazine. Press STOP twice
PLC_90505 – WARNING: possible collision between PANEL and AGGREGATES on REVOLVER magazine. Check the panel thickness. Press STOP twice
PLC_90506 – The axis cannot be reset as some other more important axes are not reset yet. Press STOP twice
PLC_90507 – The movement of the rotating axis is not allowed when the deflector is fitted on the electrospindle. Press STOP twice
PLC_90508 – Warning: the electrospindle might impact with other parts of the machine. Press STOP twice to stop the program or continue using the command “Disable” on the remote control unit to disable the collision control
PLC_90509 – The edgebanding strip cannot get fed. Check the optical fibre and the tracks of the edgebanding strip. Press STOP twice
PLC_90510 – WARNING: EXCESSIVE MOTOR TORQUE OF THE Rc AXIS. LUBRICATE THE GLUE ROLLER. Press STOP twice
PLC_90511 – WARNING: excessive overall dimension of the AGGREGATE/BIT to use the BLOWER on the electrospindle. Check the tooling of the electrospindle. Press STOP twice
PLC_90512 – DRYER DESCENT/ASCENT TIMEOUT: check the unit mechanically. Press STOP twice
PLC_90513 – CLOSED RING CALIBRATION: REMOVE THE EDGEBANDING STRIP FROM THE EDGE-BANDING UNIT. Press STOP twice
PLC_90514 – REMOVE THE EDGEBANDING STRIP FROM THE EDGE-BANDING UNIT. Press STOP twice
PLC_90515 – STRIP END STILL IN THE BANDING MATERIAL CONTAINER BECAUSE TOO LONG OR TOO SHORT. Check the banding material container. Press STOP twice
PLC_90516 – Error on an automatic tilting aggregate: orientation not within tolerance. Press START to continue, STOP to stop the cycle
PLC_90517 – MANUAL ENVIRONMENT selection: the push-button STOP should be maybe press twice
PLC_90518 – Axis locked because a grip piston of the roller presser is disabled. Press the presser parking push-button to continue or press STOP twice
PLC_90519 – Warning: the boring machine might impact with other parts of the machine. Press STOP twice to interrupt the program or continue by using the command “Continue” on the remote control panel
PLC_90520 – Warning: the boring machine might impact with other parts of the machine. Press STOP twice to stop the program or continue using the command “Disable” on the remote control unit to disable the collision control
PLC_90521 – The UNICLAMP enabling selector is not compatible with the PUNI program parameter. Press STOP twice and turn the UNICLAMP selector to the right position
PLC_90522 – The vibrometer is enabled in the PLC but the Master device is not ready
PLC_90523 – Warning PLUTO: (Nr.,UE)
PLC_90524 –
PLC_90525 –
PLC_90526 –
PLC_90527 –
PLC_90528 –
PLC_90529 –
PLC_90530 –
PLC_90531 –
PLC_90532 –
PLC_90533 –
PLC_90534 –
PLC_90535 –
PLC_90536 –
PLC_90537 –
PLC_90538 –
PLC_90539 –
PLC_90540 –
PLC_90541 –
PLC_90542 –
PLC_90543 –
PLC_90544 –
PLC_90545 –
PLC_90546 –
PLC_90547 –
PLC_90548 –
PLC_90549 –
PLC_90550 –
PLC_90551 –
PLC_90552 –
PLC_90553 –
PLC_90554 –
PLC_90555 –
PLC_90556 –
PLC_90557 –
PLC_90558 –
PLC_90559 –
PLC_90560 –
PLC_90561 –
PLC_90562 –
PLC_90563 –
PLC_90564 –
PLC_90565 –
PLC_90566 –
PLC_90567 –
PLC_90568 –
PLC_90569 –
PLC_90570 –
PLC_90571 –
PLC_90572 –
PLC_90573 –
PLC_90574 –
PLC_90575 – Error during movement of the loading arm clamp drive piston
PLC_90576 – Error during movement of the loading arm clamp opening piston
PLC_90577 – Error during movement of the loading arm clamp rotation piston
PLC_90578 – Error during movement of the multiple panel X pushing piston
PLC_90579 – Error during movement of the multiple panel Y pushing piston
PLC_90580 – Clamp closed during panel movement
PLC_90581 – Warning: panel not held by the pusher
PLC_90582 – Panel thickness less than the minimum value
PLC_90583 – Thickness of the last stack piece less than the minimum value
PLC_90584 – X pusher safety sensor activated
PLC_90585 – Maximum torque percentage exceeded during loading with X pusher
PLC_90586 – Panel loading with floating clamps of the loading/unloading arm
PLC_90587 – Panel loading without rotation of the clamps of the loading/unloading arm
PLC_90588 – Panel loading with forced rotation of the clamps of the loading/unloading arm
PLC_90589 – Panel stack height insufficient for performing a new loading operation
PLC_90590 – Error in multiple panel clamp data
PLC_90591 – Error in multiple panel pusher data
PLC_90592 –
PLC_90593 –
PLC_90594 –
PLC_90595 – Machine in suspension mode due to panel output safety or safety card
PLC_90596 –
PLC_90597 –
PLC_90598 – Possible colision between stops and a panel cell element
PLC_90599 – Printer not powered – check the thermomagnetic switches on the loading pallet
PLC_90600 – Waiting vacuum ON in RH area
PLC_90601 – Waiting vacuum OFF in RH area
PLC_90602 – Waiting vacuum ON in LH area
PLC_90603 – Waiting vacuum OFF in LH area
PLC_90604 – Error: impossible loading multiple thin panels
PLC_90605 – Error in moving piston of the Loading pallet Microswitch
PLC_90606 – Error in sweeping arm fall down posizion
PLC_90607 – Unloading Pallet Emergency. Check the emergency switch
PLC_90608 – Warning: Sweeping in down position
PLC_90609 – Alarm TP Motor temperature sensor
PLC_90610 – Attention: the ascent of the scissor mechanism has been commanded with the loading pallet axis incorrectly positioned. Check the safety sensor.
PLC_90611 – Error: sweeping arm pistons not up
PLC_90612 – Cannot move the axes: move the Xc axis up to the positive software limit switch or to a position upper than home position
PLC_90613 – Error in positioning of unloading pallet
PLC_90614 – Error in moving mobile stops of the unloading pallet type 4
PLC_90615 – Error in the movement of unloading pallet type 4
PLC_90616 – Error in moving the loading pallet type 7
PLC_90617 – Error in moving the X side stop of the loading pallet
PLC_90618 – Error in positioning of loading pallet
PLC_90619 – Error: Impossible load more than one panel
PLC_90620 – Safety switching box. Emergengy – Unloading panel security switch pressed with Sweeping Arm in down position
PLC_90621 – Safety Module. Partial security bypass
PLC_90622 – Safety Module. Total security bypass
PLC_90624 – Safety Module. To restore the loading pallet power may be necessary the reset of the safety fence
PLC_90625 – Safety Module. Machine Emergency for loading pallet photocells shadowed with the safety fence opened
PLC_90626 – Safety switching box. Loading pallet barriers occupied. To reset the pallet, free the photocells and press the green button on the pallet console
PLC_90627 – Safety switching box. Line emergency.
PLC_90628 – Safety switching box. Loading pallet emergency from external device.
PLC_90629 – RESET not accepted, restoring protection-barriers in progress
PLC_90630 –
PLC_90631 –
PLC_90632 –
PLC_90633 –
PLC_90634 –
PLC_90635 –
PLC_90636 –
PLC_90637 –
PLC_90638 –
PLC_90639 –
PLC_90640 –
PLC_90641 –
PLC_90642 –
PLC_90643 –
PLC_90644 –
PLC_90645 –
PLC_90646 –
PLC_90647 –
PLC_90648 –
PLC_90649 –
PLC_90650 –
PLC_90651 –
PLC_90652 –
PLC_90653 –
PLC_90654 –
PLC_90655 –
PLC_90656 –
PLC_90657 –
PLC_90658 –
PLC_90659 –
PLC_90660 –
PLC_90661 –
PLC_90662 –
PLC_90663 –
PLC_90664 –
PLC_90665 –
PLC_90666 –
PLC_90667 –
PLC_90668 –
PLC_90669 –
PLC_90670 –
PLC_90671 –
PLC_90672 –
PLC_90673 –
PLC_90674 –
PLC_90675 –
PLC_90676 –
PLC_90677 –
PLC_90678 –
PLC_90679 –
PLC_90680 –
PLC_90681 –
PLC_90682 –
PLC_90683 –
PLC_90684 –
PLC_90685 –
PLC_90686 –
PLC_90687 –
PLC_90688 –
PLC_90689 –
PLC_90690 –
PLC_90691 –
PLC_90692 –
PLC_90693 –
PLC_90694 –
PLC_90695 –
PLC_90696 –
PLC_90697 –
PLC_90698 –
PLC_90699 –
PLC_90700 – Movement error of the Y-horizontal pusher of the loading pallet with low pressure
PLC_90701 – Movement error of the X pusher fixed suction cup, fitted on the loading pallet type 2
PLC_90702 – Movement error of the X pusher mobile suction cup fitted on the loading pallet type 2
PLC_90703 – Error in activation of vacuum on the fixed suction cup piston for the X-pusher of the loading pallet
PLC_90704 – Error in activation of vacuum on the mobile suction cup piston for the X-pusher of the loading pallet
PLC_90705 – Movement error of the loading pallet Y-horizontal additional pusher
PLC_90706 – Movement error of the loading pallet Y-horizontal additional pusher with low pressure
PLC_90707 – Movement error of the loading pallet Y-vertical additional pusher
PLC_90708 – Error in activation of vacuum on suction cups of the additional Y pusher of the loading pallet (type 2)
PLC_90709 – Movement error of the fixed suction cup of the thin panels kit (short stroke)
PLC_90710 – Movement error of the mobile suction cup of the thin panels kit (short stroke)
PLC_90711 – Movement error of the limit switch piston of the thin panels kit suction cups
PLC_90712 – Loading table KO: Top loading input active (no stack) – Err:
PLC_90713 – Loading table KO: Safety micro input active – Err:
PLC_90714 – Loading table KO: Loading table time-out – Err:
PLC_90715 – Loading table KO: End of stack from photocells – Err:
PLC_90716 – Loading table KO: Encoder safety position reached – Err:
PLC_90717 – Loading table KO: Encoder position less than minimum half-panel – Err:
PLC_90718 – Loading table KO: First position measured by the encoder greater than the second – Err:
PLC_90719 –
PLC_90720 –
PLC_90721 –
PLC_90722 –
PLC_90723 –
PLC_90724 –
PLC_90725 –
PLC_90726 –
PLC_90727 –
PLC_90728 –
PLC_90729 –
PLC_90730 –
PLC_90731 –
PLC_90732 –
PLC_90733 –
PLC_90734 –
PLC_90735 –
PLC_90736 –
PLC_90737 –
PLC_90738 –
PLC_90739 –
PLC_90740 –
PLC_90741 –
PLC_90742 –
PLC_90743 –
PLC_90744 –
PLC_90745 –
PLC_90746 –
PLC_90747 –
PLC_90748 –
PLC_90749 –
PLC_90750 –
PLC_90751 –
PLC_90752 –
PLC_90753 –
PLC_90754 –
PLC_90755 –
PLC_90756 –
PLC_90757 –
PLC_90758 –
PLC_90759 –
PLC_90760 –
PLC_90761 –
PLC_90762 –
PLC_90763 –
PLC_90764 –
PLC_90765 –
PLC_90766 –
PLC_90767 –
PLC_90768 –
PLC_90769 –
PLC_90770 –
PLC_90771 –
PLC_90772 –
PLC_90773 –
PLC_90774 –
PLC_90775 –
PLC_90776 –
PLC_90777 –
PLC_90778 –
PLC_90779 –
PLC_90780 –
PLC_90781 –
PLC_90782 –
PLC_90783 –
PLC_90784 –
PLC_90785 –
PLC_90786 –
PLC_90787 –
PLC_90788 –
PLC_90789 –
PLC_90790 –
PLC_90791 –
PLC_90792 –
PLC_90793 –
PLC_90794 –
PLC_90795 –
PLC_90796 –
PLC_90797 –
PLC_90798 –
PLC_90799 –
PLC_90800 –
PLC_90801 –
PLC_90802 –
PLC_90803 –
PLC_90804 –
PLC_90805 –
PLC_90806 –
PLC_90807 –
PLC_90808 –
PLC_90809 –
PLC_90810 –
PLC_90811 –
PLC_90812 –
PLC_90813 –
PLC_90814 –
PLC_90815 –
PLC_90816 –
PLC_90817 –
PLC_90818 –
PLC_90819 –
PLC_90820 –
PLC_90821 –
PLC_90822 –
PLC_90823 –
PLC_90824 –
PLC_90825 –
PLC_90826 –
PLC_90827 –
PLC_90828 –
PLC_90829 –
PLC_90830 –
PLC_90831 –
PLC_90832 –
PLC_90833 –
PLC_90834 –
PLC_90835 –
PLC_90836 –
PLC_90837 –
PLC_90838 –
PLC_90839 –
PLC_90840 –
PLC_90841 –
PLC_90842 –
PLC_90843 –
PLC_90844 –
PLC_90845 –
PLC_90846 –
PLC_90847 –
PLC_90848 –
PLC_90849 –
PLC_90850 –
PLC_90851 –
PLC_90852 –
PLC_90853 –
PLC_90854 –
PLC_90855 –
PLC_90856 –
PLC_90857 –
PLC_90858 –
PLC_90859 –
PLC_90860 –
PLC_90861 –
PLC_90862 –
PLC_90863 –
PLC_90864 –
PLC_90865 –
PLC_90866 –
PLC_90867 –
PLC_90868 –
PLC_90869 –
PLC_90870 –
PLC_90871 –
PLC_90872 –
PLC_90873 –
PLC_90874 –
PLC_90875 –
PLC_90876 –
PLC_90877 –
PLC_90878 –
PLC_90879 –
PLC_90880 –
PLC_90881 –
PLC_90882 –
PLC_90883 –
PLC_90884 –
PLC_90885 –
PLC_90886 –
PLC_90887 –
PLC_90888 –
PLC_90889 –
PLC_90890 –
PLC_90891 –
PLC_90892 –
PLC_90893 –
PLC_90894 –
PLC_90895 –
PLC_90896 –
PLC_90897 –
PLC_90898 –
PLC_90899 –
PLC_90900 – Oscillating Knife is active
PLC_90901 – Attention: Optiscout connected with the machine
PLC_90902 – Program succesfully generated by Optiscout
PLC_90903 – Program succesfully generated by Optiscout
PLC_90904 –
PLC_90905 –
PLC_90906 –
PLC_90907 –
PLC_90908 –
PLC_90909 –
PLC_90910 –
PLC_90911 –
PLC_90912 –
PLC_90913 –
PLC_90914 –
PLC_90915 –
PLC_90916 –
PLC_90917 –
PLC_90918 –
PLC_90919 –
PLC_90920 –
PLC_90921 –
PLC_90922 –
PLC_90923 –
PLC_90924 –
PLC_90925 –
PLC_90926 –
PLC_90927 –
PLC_90928 –
PLC_90929 –
PLC_90930 –
PLC_90931 –
PLC_90932 –
PLC_90933 –
PLC_90934 –
PLC_90935 –
PLC_90936 –
PLC_90937 –
PLC_90938 –
PLC_90939 –
PLC_90940 –
PLC_90941 –
PLC_90942 –
PLC_90943 –
PLC_90944 –
PLC_90945 –
PLC_90946 –
PLC_90947 –
PLC_90948 –
PLC_90949 –
PLC_90950 –
PLC_90951 –
PLC_90952 –
PLC_90953 –
PLC_90954 –
PLC_90955 –
PLC_90956 –
PLC_90957 –
PLC_90958 –
PLC_90959 –
PLC_90960 –
PLC_90961 –
PLC_90962 –
PLC_90963 –
PLC_90964 –
PLC_90965 –
PLC_90966 –
PLC_90967 –
PLC_90968 –
PLC_90969 –
PLC_90970 –
PLC_90971 –
PLC_90972 –
PLC_90973 –
PLC_90974 –
PLC_90975 –
PLC_90976 –
PLC_90977 –
PLC_90978 –
PLC_90979 –
PLC_90980 –
PLC_90981 –
PLC_90982 –
PLC_90983 –
PLC_90984 –
PLC_90985 –
PLC_90986 –
PLC_90987 –
PLC_90988 –
PLC_90989 –
PLC_90990 –
PLC_90991 –
PLC_90992 –
PLC_90993 –
PLC_90994 –
PLC_90995 –
PLC_90996 –
PLC_90997 –
PLC_90998 –
PLC_90999 –
PLC_91000 –
PLC_91001 –
PLC_91002 –
PLC_91003 –
PLC_91004 –
PLC_91005 –
PLC_91006 –
PLC_91007 –
PLC_91008 –
PLC_91009 –
PLC_91010 –
PLC_91011 –
PLC_91012 –
PLC_91013 –
PLC_91014 –
PLC_91015 –
PLC_91016 –
PLC_91017 –
PLC_91018 –
PLC_91019 –
PLC_91020 –
PLC_91021 –
PLC_91022 –
PLC_91023 –
PLC_91024 –
PLC_91025 –
PLC_91026 –
PLC_91027 –
PLC_91028 –
PLC_91029 –
PLC_91030 –
PLC_91031 –
PLC_91032 –
PLC_91033 –
PLC_91034 –
PLC_91035 –
PLC_91036 –
PLC_91037 –
PLC_91038 –
PLC_91039 –
PLC_91040 –
PLC_91041 –
PLC_91042 –
PLC_91043 –
PLC_91044 –
PLC_91045 –
PLC_91046 –
PLC_91047 –
PLC_91048 –
PLC_91049 –
PLC_91050 –
PLC_91051 –
PLC_91052 –
PLC_91053 –
PLC_91054 –
PLC_91055 –
PLC_91056 –
PLC_91057 –
PLC_91058 –
PLC_91059 –
PLC_91060 –
PLC_91061 –
PLC_91062 –
PLC_91063 –
PLC_91064 –
PLC_91065 –
PLC_91066 –
PLC_91067 –
PLC_91068 –
PLC_91069 –
PLC_91070 –
PLC_91071 –
PLC_91072 –
PLC_91073 –
PLC_91074 –
PLC_91075 –
PLC_91076 –
PLC_91077 –
PLC_91078 –
PLC_91079 –
PLC_91080 –
PLC_91081 –
PLC_91082 –
PLC_91083 –
PLC_91084 –
PLC_91085 –
PLC_91086 –
PLC_91087 –
PLC_91088 –
PLC_91089 –
PLC_91090 –
PLC_91091 –
PLC_91092 –
PLC_91093 –
PLC_91094 –
PLC_91095 –
PLC_91096 –
PLC_91097 –
PLC_91098 –
PLC_91099 –
PLC_91100 –
PLC_91101 –
PLC_91102 –
PLC_91103 –
PLC_91104 –
PLC_91105 –
PLC_91106 –
PLC_91107 –
PLC_91108 –
PLC_91109 –
PLC_91110 –
PLC_91111 –
PLC_91112 –
PLC_91113 –
PLC_91114 –
PLC_91115 –
PLC_91116 –
PLC_91117 –
PLC_91118 –
PLC_91119 –
PLC_91120 –
PLC_91121 –
PLC_91122 –
PLC_91123 –
PLC_91124 –
PLC_91125 –
PLC_91126 –
PLC_91127 –
PLC_91128 –
PLC_91129 –
PLC_91130 –
PLC_91131 –
PLC_91132 –
PLC_91133 –
PLC_91134 –
PLC_91135 –
PLC_91136 –
PLC_91137 –
PLC_91138 –
PLC_91139 –
PLC_91140 –
PLC_91141 –
PLC_91142 –
PLC_91143 –
PLC_91144 –
PLC_91145 –
PLC_91146 –
PLC_91147 –
PLC_91148 –
PLC_91149 –
PLC_91150 –
PLC_91151 –
PLC_91152 –
PLC_91153 –
PLC_91154 –
PLC_91155 –
PLC_91156 –
PLC_91157 –
PLC_91158 –
PLC_91159 –
PLC_91160 –
PLC_91161 –
PLC_91162 –
PLC_91163 –
PLC_91164 –
PLC_91165 –
PLC_91166 –
PLC_91167 –
PLC_91168 –
PLC_91169 –
PLC_91170 –
PLC_91171 –
PLC_91172 –
PLC_91173 –
PLC_91174 –
PLC_91175 –
PLC_91176 –
PLC_91177 –
PLC_91178 –
PLC_91179 –
PLC_91180 –
PLC_91181 –
PLC_91182 –
PLC_91183 –
PLC_91184 –
PLC_91185 –
PLC_91186 –
PLC_91187 –
PLC_91188 –
PLC_91189 –
PLC_91190 –
PLC_91191 –
PLC_91192 –
PLC_91193 –
PLC_91194 –
PLC_91195 –
PLC_91196 –
PLC_91197 –
PLC_91198 –
PLC_91199 –
PLC_91200 – Vertical release of the mobile suction-cup bar.
PLC_91201 – Fixed bar vacuum.
PLC_91202 – Panel presser for jig shutter activation.
PLC_91203 – Stacker blow.
PLC_91204 – Column block.
PLC_91205 – Mobile bar vacuum.
PLC_91206 – Low pressure for pushing in X.
PLC_91207 – Low pressure for pushing in Y.
PLC_91208 – Blower for panel cleaning.
PLC_91209 – Loading thickness tracer not ready.
PLC_91210 – Loading stack not found.
PLC_91211 – Unloading thickness tracer not ready.
PLC_91212 – Unloading stack not found.
PLC_91213 – Panel cannot be deposited on the unloading stack: stack too high.
PLC_91214 – Thickness tracer not occupied: panel lost.
PLC_91215 – The photocells for emergency suction cup bar descent have been intercepted.
PLC_91216 – Stack origin valve.
PLC_91217 – Stacker brake.
PLC_91218 – Stacker blade.
PLC_91219 – Synchro thermomagnetic switches KO.
PLC_91220 – Synchro resistors KO.
PLC_91221 – Stack origin device not idle; reset manually.
PLC_91222 – Detaching device:loading stack too high.
PLC_91223 – Stack origin device cannot be used: interference with detaching device.
PLC_91224 – Zsm and Zm tracing positions are incoherent.
PLC_91225 – Pusher device not ready.
PLC_91226 –
PLC_91227 –
PLC_91228 –
PLC_91229 – Uniclamp mode not compatible with Synchro.
PLC_91230 – Panel dimensions not coherent with Synchro limits.
PLC_91231 –
PLC_91232 –
PLC_91233 –
PLC_91234 –
PLC_91235 –
PLC_91236 –
PLC_91237 –
PLC_91238 –
PLC_91239 –
PLC_91240 –
PLC_91241 –
PLC_91242 –
PLC_91243 –
PLC_91244 –
PLC_91245 –
PLC_91246 –
PLC_91247 –
PLC_91248 –
PLC_91249 –
PLC_91250 –
PLC_91251 –
PLC_91252 –
PLC_91253 –
PLC_91254 –
PLC_91255 –
PLC_91256 –
PLC_91257 –
PLC_91258 –
PLC_91259 –
PLC_91260 –
PLC_91261 –
PLC_91262 –
PLC_91263 –
PLC_91264 –
PLC_91265 –
PLC_91266 –
PLC_91267 –
PLC_91268 –
PLC_91269 –
PLC_91270 –
PLC_91271 –
PLC_91272 –
PLC_91273 –
PLC_91274 –
PLC_91275 –
PLC_91276 –
PLC_91277 –
PLC_91278 –
PLC_91279 –
PLC_91280 –
PLC_91281 –
PLC_91282 –
PLC_91283 –
PLC_91284 –
PLC_91285 –
PLC_91286 –
PLC_91287 –
PLC_91288 –
PLC_91289 –
PLC_91290 –
PLC_91291 –
PLC_91292 –
PLC_91293 –
PLC_91294 –
PLC_91295 –
PLC_91296 –
PLC_91297 –
PLC_91298 –
PLC_91299 –
PLC_91300 –
MSG_PLC_0 – Remaining labels:
MSG_PLC_1 – Remaining labels fewer than the minimum value:
MSG_PLC_2 – Replace the roll and reset the counter.
MSG_PLC_3 – Remaining ribbon length (m):
MSG_PLC_4 – Remaining ribbon length shorter than the minimum value (m):
MSG_PLC_5 – Replace the ribbon and reset the counter.
MSG_PLC_6 – The ribbon is enough for the number of labels:
MSG_PLC_7 –
MSG_PLC_8 –
MSG_PLC_9 –
MSG_PLC_10 –
MSG_PLC_11 – Two- hand control option. Inconsistency between the PLC tables and the safety box
MSG_PLC_12 – Photocell barrier option. Inconsistency between the PLC tables and the safety box
MSG_PLC_13 – Mobile curtain guards optionInconsistency between the PLC tables and the safety box
MSG_PLC_14 – EPS optionInconsistency between the PLC tables and the safety box
MSG_PLC_15 – Slow machine option. Inconsistency between the PLC tables and the safety box
MSG_PLC_16 – Single area optionInconsistency between the PLC tables and the safety box
MSG_PLC_17 –
MSG_PLC_18 –
MSG_PLC_19 –
MSG_PLC_20 –
MSG_PLC_21 –
MSG_PLC_22 –
MSG_PLC_23 –
MSG_PLC_24 –
MSG_PLC_25 –
MSG_PLC_26 –
MSG_PLC_27 –
MSG_PLC_28 –
MSG_PLC_29 –
MSG_PLC_30 –
MSG_PLC_31 –
MSG_PLC_32 – Second inverter option. Inconsistency between the PLC tables and the safety box
MSG_PLC_33 – Rover Edge optionInconsistency between the PLC tables and the safety box
MSG_PLC_34 – Second Y axis option. Inconsistency between the PLC tables and the safety box
MSG_PLC_35 – Robot presence option. Inconsistency between the PLC tables and the safety box
MSG_PLC_36 –
MSG_PLC_37 –
MSG_PLC_38 –
MSG_PLC_39 –
MSG_PLC_40 –
MSG_PLC_41 –
MSG_PLC_42 –
MSG_PLC_43 –
MSG_PLC_44 –
MSG_PLC_45 –
MSG_PLC_46 –
MSG_PLC_47 –
MSG_PLC_48 –
MSG_PLC_49 –
MSG_PLC_50 –
MSG_PLC_51 – Unloading Pallet option. Inconsistency between the PLC tables and the safety box
MSG_PLC_52 – Loading Pallet option. Inconsistency between the PLC tables and the safety box
MSG_PLC_53 –
MSG_PLC_54 –
MSG_PLC_55 –
MSG_PLC_56 –
MSG_PLC_57 –
MSG_PLC_58 –
MSG_PLC_59 –
MSG_PLC_60 –
MSG_PLC_61 –
MSG_PLC_62 –
MSG_PLC_63 –
MSG_PLC_64 –
MSG_PLC_65 –
MSG_PLC_66 –
MSG_PLC_67 –
MSG_PLC_68 –
MSG_PLC_69 –
MSG_PLC_70 –
MSG_PLC_71 –
MSG_PLC_72 –
MSG_PLC_73 –
MSG_PLC_74 –
MSG_PLC_75 –
MSG_PLC_76 –
MSG_PLC_77 –
MSG_PLC_78 –
MSG_PLC_79 –
MSG_PLC_80 –
MSG_PLC_99999 –
MSG_MS1_0 –
MSG_MS1_1 –
MSG_MS1_2 –
MSG_MS1_100 – Misalignment along Z axis:
MSG_MS1_101 – Misalignment along X axis:
MSG_MS1_102 – Misalignment along Y axis:
MSG_MS1_103 – Tolerance:
MSG_MS1_104 – Z offset measured of the presetter:
MSG_MS1_105 – X offset measured of the presetter:
MSG_MS1_106 – Y offset measured of the presetter:
MSG_MS1_107 – Laser beam thickness measured:
MSG_MS1_108 – Tool length:
MSG_MS1_109 – Tool diameter:
MSG_MS1_110 – Error in ALIGNMENT cycle.
MSG_MS1_111 – Error in CALIBRATION cycle.
MSG_MS1_112 – Error in PRESETTING cycle.
MSG_MS1_113 – Error in TOOL BREAKAGE CONTROL cycle.
MSG_MS1_114 – Tool broken.
MSG_MS1_115 – Difference between measurements:
MSG_MS1_116 – Tool rotation speed has changed: rpm=
MSG_MS1_117 – Beam error.
MSG_MS1_118 – Slide position change.
MSG_MS1_119 – Measuring TP not enabled: TP
MSG_MS1_120 – Invalid TP type: TP
MSG_MS1_121 – Invalid TP setting axis: TP
MSG_MS1_122 – Misalignment tolerance exceeded: